| 00:18.45 | *** join/#stepcode kesha_ (~kesha@49.249.8.110) |
| 03:03.43 | *** join/#stepcode kesha__ (~kesha@49.249.0.69) |
| 03:43.38 | *** join/#stepcode kesha__ (~kesha@49.249.0.143) |
| 03:56.30 | *** join/#stepcode kesha__ (~kesha@49.249.0.143) |
| 04:02.49 | *** join/#stepcode kesha__ (~kesha@49.249.0.60) |
| 05:13.29 | *** join/#stepcode kesha (~kesha@49.202.231.160) |
| 05:27.57 | *** join/#stepcode kesha_ (~kesha@49.202.238.42) |
| 06:38.10 | *** join/#stepcode kesha_ (~kesha@49.249.0.9) |
| 07:17.54 | *** join/#stepcode kesha__ (~kesha@49.249.17.97) |
| 08:47.54 | *** join/#stepcode kesha (~kesha@49.249.0.47) |
| 08:53.27 | *** join/#stepcode Gurvinder (caa43575@gateway/web/freenode/ip.202.164.53.117) |
| 08:55.23 | Gurvinder | what is stepcode used for ? |
| 08:58.29 | *** join/#stepcode kesha (~kesha@49.202.231.167) |
| 09:07.58 | *** join/#stepcode kesha (~kesha@49.202.231.167) |
| 10:11.44 | *** join/#stepcode kesha (~kesha@49.249.16.181) |
| 10:52.10 | *** join/#stepcode kesha (~kesha@49.249.16.181) |
| 11:09.10 | *** join/#stepcode kesha (~kesha@49.249.16.181) |
| 11:24.58 | *** join/#stepcode kesha (~kesha@49.249.16.181) |
| 11:58.05 | *** join/#stepcode kesha_ (~kesha@49.249.16.50) |
| 13:28.07 | *** join/#stepcode kesha_ (~kesha@49.249.200.58) |
| 17:50.25 | *** join/#stepcode GurvinderSingh (65d8c144@gateway/web/freenode/ip.101.216.193.68) |
| 17:50.38 | *** part/#stepcode GurvinderSingh (65d8c144@gateway/web/freenode/ip.101.216.193.68) |
| 17:51.14 | *** join/#stepcode GurvinderSingh (65d8c144@gateway/web/freenode/ip.101.216.193.68) |
| 17:51.53 | GurvinderSingh | Having installation problems in STEPcode |
| 17:52.46 | kesha_ | What problem ? Describe in a bit detail |
| 17:54.15 | GurvinderSingh | I have downloaded source code of STEPcode from github and following the build instruction but there are some headers files that are not found while running cmake |
| 17:54.56 | GurvinderSingh | I have also posted a mail in the mailing list |
| 17:55.29 | kesha_ | Can you paste it here > paste.kde.org |
| 17:58.34 | GurvinderSingh | http://paste.kde.org/pa9e5b787/ |
| 17:58.37 | GurvinderSingh | done |
| 18:03.22 | kesha_ | I think these are system headers and not of stepcode. Now try if is builds successfully. |
| 18:08.22 | GurvinderSingh | Again run the cmake command ?? |
| 18:09.57 | GurvinderSingh | Ran the cmake command and it build successfully |
| 18:18.09 | GurvinderSingh | Got some errors while running make command |
| 18:19.32 | GurvinderSingh | http://goo.gl/8q62Wk |
| 18:20.05 | GurvinderSingh | I have pasted the last few lines that were shown . |
| 21:32.30 | *** join/#stepcode kesha_ (~kesha@49.249.200.58) |
| 21:59.26 | *** join/#stepcode mpictor (~mark@c-67-177-102-131.hsd1.in.comcast.net) |