| 00:06.05 | *** join/#nslu2-linux HopsNBarley (n=andy24@pool-71-116-66-86.snfcca.dsl-w.verizon.net) |
| 00:06.26 | Sinclair73de | oh... possible my usb-stick is dead |
| 00:07.11 | RobNC | THat's always better than bad soldering or NSLU2 board problem :-) |
| 00:07.57 | Sinclair73de | yes... but doing d-i again.... :-( |
| 00:10.37 | RobNC | D-I yes it takes forever for some reason... think it's the mirror site speed |
| 00:11.20 | Sinclair73de | hmmm |
| 00:11.51 | RobNC | yeah the D-I instructions aren't clear or up-to-date for the latest etch install |
| 00:12.36 | Sinclair73de | possible too hot for my usb-stick inside the slug see: http://stposch2.dyndns.info/temp/IMG_1108.JPG |
| 00:12.49 | Sinclair73de | outside its running again |
| 00:12.53 | RobNC | but the good thing is it's a lot smoother than my previous install circa March whereby most of the kernel modules weren't set up right, and apt wasn't set up correctly either. It's come a long way and works great. Just wish I could manually select which packages I want and don't want. |
| 00:13.00 | Sinclair73de | but soldering is good |
| 00:13.49 | RobNC | what is that board above the memory? |
| 00:14.18 | Sinclair73de | serial |
| 00:14.28 | Sinclair73de | with max3232 |
| 00:16.43 | RobNC | Ah I did mine with superglue above the memory (double-stacked) with flipping the chip over and using 30ga wire or thicker for Vcc/Vss |
| 00:16.43 | RobNC | don't have pics b/c using it right now but should take some pics next time |
| 00:16.43 | RobNC | green/white/blk/red = JTAG? |
| 00:16.56 | Sinclair73de | scsi 0:0:0:0: rejecting I/O to dead device |
| 00:17.00 | Sinclair73de | my stick ... :-( |
| 00:17.33 | RobNC | I glued a 4x2 header onto back of my SLUG for JTAG - used same pinout as WRT54G JTAG (only uses 4 signals and ground) |
| 00:17.51 | Sinclair73de | no... wires for the usb-stick when placed inside the SLUG |
| 00:18.16 | RobNC | Oh that stinks... time to unwrap tape. So you're using one of the three unused USB ports on the backside? |
| 00:18.26 | Sinclair73de | now the stick is connected normaly, and still dead |
| 00:18.28 | Sinclair73de | yes |
| 00:18.55 | RobNC | ah gotcha... those flash devices won't last forever (read/write cycles) |
| 00:19.20 | Sinclair73de | not so old, but cheap |
| 00:20.39 | RobNC | yeah true... I'd be afraid of a permanent mod like that. Just using seagate HDDs with USB2 cases now. Would be nice to use extra USB ports for diskless operation, but not using it for that now |
| 00:21.56 | RobNC | It's too bad there isn't software to determine if all "free" sectors (swapped out when bad sectors are found by microcontroller) are used. Thus, the useful life would be over at that point. |
| 00:23.08 | Sinclair73de | this is the serial board from top http://stposch2.dyndns.info/temp/IMG_0911.JPG |
| 00:23.56 | RobNC | I was too poor to pay for that, and had some scrap boards at work that I used. Max3202 is what I used |
| 00:24.24 | Sinclair73de | my idea was to use the slug with system on internal stick an an usb-hdd for large data-space |
| 00:25.11 | Sinclair73de | the chip was a sample from maxim and the board is selfmade you see |
| 00:25.36 | RobNC | is there an advantage of that over USB-HDD for large user-data? Other than power and noise savings... |
| 00:26.33 | Sinclair73de | more portable... sometimes i what use these Slug for internet radio in outher rooms here |
| 00:27.53 | RobNC | oh I gotcha... |
| 00:28.26 | Sinclair73de | but... no way... must install to hdd again |
| 00:28.43 | RobNC | this is true. How about 2.5" laptop HDD |
| 00:29.11 | RobNC | most can be USB powered |
| 00:44.04 | Sinclair73de | i have too slugs and 2 old laptop HDD's (3GB and 5GB) |
| 00:44.12 | Sinclair73de | too = 2 |
| 00:47.56 | chacko | robnc: I use 2.5" HDD exclusively here with a couple of slugs, one unslung, the other slugos/be. I have a couple of spare ones which I do a full backup to. They work fine, some people say the life will be limited. |
| 00:49.05 | chacko | You can use those old HDD as well, most of the older ones will easily be usb powered, many new ones need additional power, especially during the startup |
| 00:53.22 | Sinclair73de | hmmm... i found, some hdd's are too slow with init , when using apex the slug boots faster than the hdd inits, and then boot fails |
| 00:54.33 | chacko | One way to get around that is to get the hdd powered up first, and then start the slug. |
| 00:55.45 | chacko | I have those usb cables, which have two usb connectors at one end, so the second one is used for addtiional power. |
| 00:57.08 | chacko | On my slugos/be, I can plug in the disk (already powered up) into DISK1 slot, soon afer I have started the powerup of the slug. |
| 00:59.49 | Sinclair73de | no good news... system hangs when copy large data |
| 01:03.31 | Sinclair73de | ok, must retry it without the stick... tomorrow |
| 01:04.12 | Sinclair73de | now sleeping... ;-) ist 2:00AM local time |
| 01:04.19 | Sinclair73de | bye bye |
| 01:17.07 | RobNC | oops I was away... ttyl |
| 01:37.26 | CIA-8 | 03rwhitby * r94 10slugimage/trunk/ (4 files in 3 dirs): Added apex small-kernel test (which currently fails), and the man page written by Joey Hess. |
| 01:43.43 | rwhitby | Chacko-away: away status is better shown by the built-in support (i.e. see they people who are greyed out in the user list?) then it doesn't cause message traffic in the channel (which makes people look in the channel to see what is being discussed, and then they are irritated cause it's just a useless away message) |
| 01:51.40 | *** join/#nslu2-linux bullet (n=bullet@73.193.62.81.cust.bluewin.ch) |
| 02:32.21 | [g2] | rwhitby optware looks like it's building crosstool and the old 2.4.22 kernel |
| 02:35.33 | rwhitby | [g2]: that's correct, for the nslu2 target (which is compatible with stock firmware) |
| 02:35.55 | rwhitby | for slugosbe target, it uses the latest slugos cross compiler built by OE |
| 03:04.29 | CIA-8 | 03rwhitby * r95 10slugimage/trunk/ (slugimage tests/apex/small-kernel.expected): Fixed the apex small kernel bug, and cleaned up the partition allocation code a bit (now that I have a regression test suite in place). |
| 03:08.23 | *** join/#nslu2-linux mithro (n=tim@ppp246-117.static.internode.on.net) |
| 03:12.36 | CIA-8 | 03rwhitby * r96 10slugimage/trunk/tests/runtests: Clean up the text executor. |
| 03:15.02 | CIA-8 | 03rwhitby * r97 10slugimage/trunk/tests/ (10 files in 4 dirs): Test files actually require bash. |
| 03:22.00 | CIA-8 | 03rwhitby * r98 10slugimage/trunk/tests/ (11 files in 4 dirs): Actually, the tests just needed a portable way of creating a temporary file, instead of calling the Debian tempfile utility. |
| 03:23.18 | CIA-8 | 03rwhitby * r99 10slugimage/trunk/tests/do-test: do-test also needed a portable way of creating a temporary file, instead of calling the Debian tempfile utility. |
| 03:31.57 | CIA-8 | 03rwhitby * r100 10slugimage/trunk/tests/ (8 files in 4 dirs): Seems that hexdump output is based on LANG settings, so canonicalise that. |
| 03:34.32 | CIA-8 | 03rwhitby * r101 10slugimage/trunk/tests/ (8 files in 4 dirs): Update the expected outputs to be LANG=C |
| 03:35.44 | rwhitby | slugimage now has a fairly good regression test suite. |
| 03:54.32 | RobNC | anyone know of a cleaner way to stop/start services than update-rc.d ? |
| 04:09.28 | CIA-8 | 03bzhou * r4901 10optware/trunk/ (Makefile make/mutt.mk): mutt: fixed -I/opt/include for gcc4 cross compilation; promoted for slugosbe |
| 04:50.41 | *** join/#nslu2-linux tuv (n=tuv@unaffiliated/tuv) |
| 05:05.15 | *** join/#nslu2-linux _G` (n=Sinclair@p54A086D4.dip0.t-ipconnect.de) |
| 06:05.58 | CIA-8 | 03bzhou * r4902 10optware/trunk/make/libogg.mk: libogg: fixed gcc4 cross compilation |
| 06:06.01 | CIA-8 | 03bzhou * r4903 10optware/trunk/make/audiofile.mk: audiofile: fixed gcc4 cross compilation |
| 06:06.04 | CIA-8 | 03bzhou * r4904 10optware/trunk/make/esound.mk: esound: fixed gcc4 cross compilation |
| 06:06.07 | CIA-8 | 03bzhou * r4905 10optware/trunk/make/libvorbis.mk: libvorbis: fixed gcc4 cross compilation |
| 06:06.14 | CIA-8 | 03bzhou * r4906 10optware/trunk/make/ivorbis-tools.mk: ivorbis-tools: fixed gcc4 cross compilation |
| 06:06.22 | CIA-8 | 03bzhou * r4907 10optware/trunk/make/gift.mk: gift: fixed gcc4 cross compilation |
| 06:09.38 | CIA-8 | 03bzhou * r4908 10optware/trunk/Makefile: promoted esound, gift*, ivorbis-tools, libvorbis, streamripper, & vorbis-tools for slugosbe |
| 06:43.24 | *** join/#nslu2-linux jacques (n=jacques@nslu2-linux/jacques) |
| 06:43.39 | *** part/#nslu2-linux jacques (n=jacques@nslu2-linux/jacques) |
| 06:45.27 | *** join/#nslu2-linux DrZimmerman (n=theo@84-72-181-62.dclient.hispeed.ch) |
| 07:11.23 | CIA-8 | 03bzhou * r4909 10optware/trunk/Makefile: promoted esniper for slugosbe |
| 08:10.08 | *** join/#nslu2-linux l0c4lh0st (n=a@89.98.192.9) |
| 08:13.44 | *** join/#nslu2-linux likewise (n=chatzill@atwork-98.r-212.178.104.atwork.nl) |
| 08:14.04 | likewise | morning all |
| 08:14.22 | likewise | NAiL: ping |
| 08:57.31 | *** join/#nslu2-linux jelle (n=jpalten@ip54518e8c.direct-adsl.nl) |
| 09:23.36 | NAiL | likewise: morning |
| 09:28.50 | NAiL | I've replaced all the caps. But I'm still getting the (apparently) PCI-related crash. It crashed before replacing the caps too, so I suspect a b0rked kernel. |
| 09:29.38 | NAiL | If not, I think the board is more or less dead. |
| 09:33.56 | likewise | NAiL: OK, I just wanted to ask if I should send you the caps. |
| 09:34.06 | likewise | or maybe a flash chip |
| 09:34.39 | NAiL | I've got two flash chips, need to check if they will work. |
| 09:37.32 | NAiL | What chips will work? |
| 09:37.51 | NAiL | I've got two flash chips that used to be bioses on something else |
| 09:40.50 | likewise | I got the caps here at work, but the flash chip at home. But I think I mentioned in the wiki page. |
| 09:41.15 | *** join/#nslu2-linux pleemans (n=peter@d51A5E612.access.telenet.be) |
| 09:49.41 | NAiL | but what I'm looking for is primarily a 256kb (2mbit) part, right? |
| 09:49.54 | NAiL | Or 512kb if I flash both halves? |
| 09:50.41 | NAiL | There isn't any harm in trying to flash the chips and seeing if it works, is there? ;) |
| 09:55.16 | *** join/#nslu2-linux Bitmaster (n=Bitmaste@c-fb61e253.325-1-64736c12.cust.bredbandsbolaget.se) |
| 10:18.57 | *** join/#nslu2-linux Jollino (i=jollino@gateway/tor/x-1c349190bf13de61) |
| 10:19.04 | Jollino | hello :) |
| 10:19.15 | Jollino | has anyone ever set up a hidden service on an unslung slug using tor? |
| 10:36.05 | *** join/#nslu2-linux AdamBaker (n=aab@userch028.dsl.pipex.com) |
| 10:42.46 | *** join/#nslu2-linux jelle (n=jpalten@ip54518e8c.direct-adsl.nl) |
| 10:54.57 | *** join/#nslu2-linux marceln (n=marceln@pion.xs4all.nl) |
| 10:55.14 | *** join/#nslu2-linux marceln (n=marceln@pion.xs4all.nl) |
| 10:59.43 | CIA-8 | 03marceln * r4910 10optware/trunk/ (Makefile make/gnokii.mk): OPTWARE: Added gnokii |
| 11:54.41 | NAiL | likewise: It would appear that it might just be the hdd that is causing my problems |
| 12:02.54 | likewise | NAiL: good to hear |
| 12:03.22 | NAiL | Not *entirely* sure yet, still gotta check a bit. But I have problems using the disk in an usb enclosure right now. |
| 12:04.07 | NAiL | which is a pain, because I don't have any replacement ATA-disks :-P |
| 12:04.07 | NAiL | S-ATA disks aplenty ;) |
| 12:17.48 | NAiL | likewise: Any pointers to how to boot from network? |
| 12:18.02 | NAiL | (Is it possible to boot from cdrom? usb?) |
| 12:18.23 | likewise | NAiL: I think you would need to build Linuxbios with a different bootloader payload |
| 12:18.31 | likewise | etherboot or such |
| 12:18.33 | NAiL | mmhmm |
| 12:18.45 | NAiL | I haven't gotten that far yet |
| 12:18.55 | NAiL | the image you gave me only supports ide? |
| 12:19.29 | likewise | NAiL: I have enabled everything in FILO (see the defconfig file in filo-0.4.2/), I am not sure it does anything beyond IDE. |
| 12:19.38 | NAiL | ah |
| 12:19.39 | NAiL | ok |
| 12:19.49 | likewise | NAiL: http://te.to/~ts1/filo/ |
| 12:20.17 | NAiL | thx |
| 12:20.51 | NAiL | I still can't boot, and I suspect it's the harddrive acting weird with the "host protected area" |
| 12:25.21 | NAiL | aha. Wrong jumper setting. Wonder if that makes a difference |
| 12:25.26 | Jollino | has anyone ever set up a hidden service on an unslung slug using tor? :) |
| 12:34.06 | NAiL | likewise: Filo 0.5 appears to have USB support |
| 12:34.58 | NAiL | Jollino: Quite possibly. Why are you asking? |
| 12:36.58 | Jollino | NAiL: because if i don't set up the hidden service, it works perfectly; if i do (it's a simple service on port 80 to 127.0.0.1:80) i keep getting a lot of "Invalid service descriptor rejected" messages, and the hidden service doesn't work |
| 12:37.31 | Jollino | privoxy immediately returns a domain not found page, rather than waiting a little |
| 12:37.35 | NAiL | ah... well.. um. No idea. |
| 12:38.46 | Jollino | i even tried removing the package and reinstalling it, just to make sure everything was clean |
| 12:53.22 | Jollino | i would compile the unstable version of tor but i have no way to crosscompile |
| 12:55.57 | rwhitby | Jollino: you don't have a PC you can run Knoppix or VMWare on? |
| 12:57.38 | Jollino | well i can run a virtual machine with linux. i actually already have slackware installed on a VM (through parallels), but i don't think it can crosscompile out of the box. how do i try it? (i never crosscompiled anything) |
| 12:57.56 | rwhitby | look at the Development section of the wiki |
| 12:58.31 | rwhitby | Debian Sarge is our default host system (that's what the autobuilders run), but Ubuntu and CentOS (RedHat) should work too |
| 12:59.34 | Jollino | i'll investigate it |
| 13:04.16 | Jollino | hmm i guess i could install optware-devel |
| 13:05.29 | rwhitby | better to cross-compile |
| 13:06.48 | Jollino | hm ok |
| 13:07.08 | Jollino | can i use ubuntu as a live cd? |
| 13:14.37 | CIA-8 | 03oleo * r4911 10optware/trunk/ (7 files in 4 dirs): buildroot: switch to gcc-4.1.1 and binutils-2.17.50.0.8 - backported lrint and lrintf C99 math to uClibc 0.9.28 |
| 13:21.52 | *** join/#nslu2-linux jelle (n=jpalten@ip54518e8c.direct-adsl.nl) |
| 13:42.25 | *** join/#nslu2-linux malfi (n=malte@e178041052.adsl.alicedsl.de) |
| 14:00.12 | *** join/#nslu2-linux bolidz (i=75-Ohm@unaffiliated/bolidz) |
| 14:00.19 | bolidz | hi |
| 14:09.59 | *** join/#nslu2-linux malfimalfi (n=malte@e178041052.adsl.alicedsl.de) |
| 14:42.32 | *** join/#nslu2-linux CIA-8 (i=cia@cia.navi.cx) |
| 14:43.16 | *** join/#nslu2-linux caplink811-log (n=caplink8@dslb-088-073-050-215.pools.arcor-ip.net) |
| 14:47.48 | NAiL | likewise: Finally got the debug info from my epia. It appears to crash when selecting scheduler (cfq or whatever it's called). Any idea why? |
| 14:49.06 | likewise | no, which kernel are you using? CFQ emits block i/o transactions to the block device driver. |
| 14:49.41 | likewise | NAiL: if you have multiple i/o schedulers built-in, you could try overriding the scheduler at the kernel parameter line. |
| 14:51.04 | NAiL | aha |
| 14:51.12 | NAiL | thx |
| 14:51.25 | *** join/#nslu2-linux GPSFan (n=kenm@12.10.255.248) |
| 14:53.53 | CIA-8 | 03oleo * r4912 10optware/trunk/ (3 files in 3 dirs): sendmail: uClibc dn_skipname solved with -DNAMED_BIND=0 |
| 14:57.55 | NAiL | likewise: no joy. BTW, would you mind sending me the caps anyway? I see one of the "new" caps I put in has started bulging |
| 14:58.32 | likewise | NAiL: sure, send me your snailmail address to leonw _ mailcan.com |
| 14:58.53 | likewise | NAiL: I'll put in an extra (double sized) FlashROM. |
| 15:01.29 | NAiL | cool, thanks :) |
| 15:04.56 | NAiL | likewise: Any idea if the Epia M10000G also works with linuxbios? |
| 15:05.45 | likewise | I dunno that device, probably should ask for on the linuxbios list. |
| 15:05.59 | NAiL | It looks more or less exactly the same |
| 15:06.06 | likewise | I know the guy that did work on the test framework, works with epia boards (coresystems.de or such) |
| 15:07.14 | NAiL | hmm.. I can't see any differences between the M10kG and the M10k |
| 15:08.18 | NAiL | I'm considering buying a new board, but I want one that can use linuxbios ;) |
| 15:08.55 | NAiL | I think that my current board is more or less junk, unless the caps fix it. |
| 15:13.52 | *** join/#nslu2-linux bullet (n=bullet@67-78.0-85.cust.bluewin.ch) |
| 15:40.27 | *** join/#nslu2-linux Jollino (n=jollino@unaffiliated/jollino) |
| 16:12.40 | *** join/#nslu2-linux gda_ (n=gda@dslb-082-083-133-152.pools.arcor-ip.net) |
| 16:20.56 | gda_ | NAiL: synology will send me a replacement side of my ds101g case :), I have only to pay for shipping |
| 16:23.19 | *** join/#nslu2-linux jelle (n=jpalten@ip54518e8c.direct-adsl.nl) |
| 16:57.38 | *** join/#nslu2-linux eiffel_ (n=eiffel@p5B0538A9.dip0.t-ipconnect.de) |
| 17:13.45 | CIA-8 | 03blaster8 * r645 10kernel/trunk/ (5 files in 3 dirs): Add Linus' fix for ext3 corruption issues spotted by Gordon, should be removed as soon as proper fix is implemented in stable/upstream |
| 17:19.08 | *** join/#nslu2-linux HopsNBarley (n=andy24@pool-71-116-66-86.snfcca.dsl-w.verizon.net) |
| 17:20.57 | NAiL | gda_: replacement side? |
| 17:27.18 | *** join/#nslu2-linux HopsNBarley (n=andy24@pool-71-116-66-86.snfcca.dsl-w.verizon.net) |
| 17:39.07 | *** join/#nslu2-linux [g2] (n=g2@nslu2-linux/g2) |
| 17:51.15 | gda_ | NAiL: a new right side of the case so that I can cut a hole for a big heatsink |
| 17:59.36 | NAiL | is your old case broken? |
| 18:10.52 | gda_ | NAiL: yesterday we talked about to mount a big heat sink to the harddisk of my ds101g |
| 18:11.50 | gda_ | for this I would have to break the case, but I don't do it without the possibility to reverse it |
| 18:12.01 | NAiL | aha |
| 18:26.38 | mwester | But without the possibility to reverse it, success is guaranteed -- as one is commited to obtaining success! :D |
| 18:28.51 | NAiL | ~rules |
| 18:28.53 | jbot | ACTION makes the rules. now stfu and code mode addons. |
| 18:29.13 | NAiL | ~rules |
| 18:29.14 | jbot | ACTION makes the rules. now stfu and code mode addons. |
| 18:30.53 | NAiL | ~nslu2-rules |
| 18:30.55 | jbot | hmm... nslu2-rules is 1) You must search the wiki before asking questions on IRC or mailing list. 2) You must follow the README steps precisely when flashing firmware. 3) Those who ask the questions, update the wiki with the answers. 4) Those who complain about doco, update the wiki to improve it. 5) Friends don't let friends flash custom firmware without ... |
| 18:31.14 | *** join/#nslu2-linux vmaster_ (i=vmaster@p549B5E91.dip.t-dialin.net) |
| 18:33.25 | NAiL | jbot: nslu2-rules is 1) Never *ever* use the Linksys EraseAll tool - it will brick your slug permanently. 2) You will search the wiki first and read the FAQ before asking questions. 3) You must read and follow the steps in the README file precisely when flashing firmware. 4) Those who ask the questions, update the wiki when they get the answers. 5) Those who complain about the documentation, update the wiki to make it better. 6) Friends don |
| 18:33.26 | jbot | ...but nslu2-rules is already something else... |
| 18:33.40 | NAiL | hmm... how did that work again |
| 18:34.20 | NAiL | jbot: forget nslu2-rules |
| 18:34.20 | jbot | i forgot nslu2-rules, NAiL |
| 18:34.26 | NAiL | jbot: nslu2-rules is 1) Never *ever* use the Linksys EraseAll tool - it will brick your slug permanently. 2) You will search the wiki first and read the FAQ before asking questions. 3) You must read and follow the steps in the README file precisely when flashing firmware. 4) Those who ask the questions, update the wiki when they get the answers. 5) Those who complain about the documentation, update the wiki to make it better. 6) Friends don |
| 18:34.28 | jbot | NAiL: okay |
| 18:34.35 | NAiL | ~nslu2-rules |
| 18:34.36 | jbot | well, nslu2-rules is 1) Never *ever* use the Linksys EraseAll tool - it will brick your slug permanently. 2) You will search the wiki first and read the FAQ before asking questions. 3) You must read and follow the steps in the README file precisely when flashing firmware. 4) Those who ask the questions, update the wiki when they get the answers. 5) Those who ... |
| 18:37.31 | CIA-8 | 03oleo * r4913 10optware/trunk/Makefile: optware: promote bsdmainutils elinks erl-escript ficy procps sdl ser snownews xcursor xfixes xft xrender for uClibc |
| 18:37.42 | NAiL | jbot: nslu2-rules is 1) Never *ever* use the Linksys EraseAll tool. 2) You will search the wiki first and read the FAQ before asking. 3) You must read and follow the steps in the README file precisely when flashing. 4) Those who ask the questions, update the wiki when they are answered. 5) Those who complain about the docu, update the wiki to improve it. 6) Friends don't let friends flash custom firmware without confirmed RedBoot Upgrade Mo |
| 18:37.43 | jbot | ...but nslu2-rules is already something else... |
| 18:37.49 | NAiL | jbot: forget nslu2-rules |
| 18:37.49 | jbot | i forgot nslu2-rules, NAiL |
| 18:38.01 | NAiL | jbot: nslu2-rules is 1) Never *ever* use the Linksys EraseAll tool. 2) You will search the wiki first and read the FAQ before asking. 3) You must read and follow the steps in the README file precisely when flashing. 4) Those who ask the questions, update the wiki when they are answered. 5) Those who complain about the docu, update the wiki to improve it. 6) Friends don't let friends flash custom firmware without confirmed RedBoot Upgrade Mo |
| 18:38.02 | jbot | okay, NAiL |
| 18:38.09 | NAiL | ~nslu2-rules |
| 18:38.10 | jbot | i heard nslu2-rules is 1) Never *ever* use the Linksys EraseAll tool. 2) You will search the wiki first and read the FAQ before asking. 3) You must read and follow the steps in the README file precisely when flashing. 4) Those who ask the questions, update the wiki when they are answered. 5) Those who complain about the docu, update the wiki to improve it. 6) ... |
| 18:40.59 | NAiL | hmm |
| 18:41.02 | NAiL | ~nail |
| 18:41.04 | jbot | ACTION nails $1 to #nslu2-linux |
| 18:41.09 | NAiL | bleh |
| 18:42.56 | CIA-8 | 03oleo * r4914 10optware/trunk/make/gnuplot.mk: gnuplot: add libstdc++ depend |
| 18:43.58 | ByronT | ~nslu2-rules |
| 18:43.59 | jbot | nslu2-rules is probably Short Ed: 1.) Use EraseAll, you're screwed. 2.) Search the wiki 1ST! 3.) Follow the README or else. 4.) If you ask, you'd better update wiki. 5.) Complain? Update the wiki 6.) Don't flash custom f/w w/o Redboot access. 7) Don't flash bootloaders w/o JTAG. |
| 18:44.34 | ByronT | ~botsnack |
| 18:44.34 | jbot | thanks, ByronT |
| 18:48.13 | CIA-8 | 03bzhou * r4915 10optware/trunk/ (Makefile make/gnokii.mk): promoted gnokii, explicit --without-x |
| 19:34.11 | *** join/#nslu2-linux yvasilev (n=yvasilev@189.140.143.44) |
| 19:43.11 | CIA-8 | 03bzhou * r4916 10optware/trunk/make/perl-dbd-sqlite.mk: perl-dbd-sqlite: 1.12 -> 1.13 |
| 19:47.58 | *** join/#nslu2-linux mithro (n=tim@ppp246-117.static.internode.on.net) |
| 19:53.02 | *** join/#nslu2-linux caplink811-log (n=caplink8@dslb-088-073-021-016.pools.arcor-ip.net) |
| 20:40.28 | CIA-8 | 03blaster8 * r646 10kernel/trunk/patches/2.6.20/ (12-fix-ext3-corruption.patch KERNEL series): Update to 2.6.20-rc1-git1, contains ext3 corruption fix |
| 20:59.59 | *** join/#nslu2-linux rwhitby (n=rwhitby@nslu2-linux/rwhitby) |
| 21:16.43 | CIA-8 | 03rwhitby * r4917 10optware/trunk/ (. make/mc.mk sources/mc/terminfo.patch): mc: Set default value for terminfo location. Closes: #5. |
| 21:19.18 | rwhitby | marceln: can you test if that solves the problem? |
| 22:07.50 | *** join/#nslu2-linux EvilDevil (n=evildevi@p54A6E908.dip.t-dialin.net) |
| 22:12.59 | CIA-8 | 03bzhou * r4918 10optware/trunk/ (Makefile make/erl-yaws.mk make/erlang.mk): promoted $(ERLANG_PACKAGES) for slugosbe |
| 22:34.32 | *** join/#nslu2-linux likewise (n=Leon_Woe@82-171-189-134.dsl.ip.tiscali.nl) |
| 22:36.57 | *** join/#nslu2-linux chacko (n=Chacko@c-67-161-27-148.hsd1.ca.comcast.net) |
| 22:39.05 | likewise | NAiL: I posted the stuff today, forgot to stick a priority label on it, but I guess everything is air-shipped these days, at least I hope so. |
| 22:45.24 | marceln | rwhitby: What problem |
| 22:45.39 | marceln | Sorry. I see it. |
| 22:47.34 | chacko | rwhitby: Hi! Yesterdat you had a suggestion for idle... So when I go away, I do not need to do anything? Somewhere in ircclient there is a setting for idle time? |
| 22:51.30 | marceln | rwhitby: It looks fine again. |
| 22:53.19 | CIA-8 | 03osas * r4919 10optware/trunk/ (make/asterisk14.mk sources/asterisk14/configs.patch): asterisk14: fix configs |
| 22:57.37 | *** join/#nslu2-linux GPSFan (n=kenm@12.10.255.248) |
| 23:09.56 | CIA-8 | 03bzhou * r4920 10optware/trunk/ (10 files in 6 dirs): use /opt/bin/update-alternatives fullpath in postinst |
| 23:39.51 | CIA-8 | 03bzhou * r4921 10optware/trunk/make/classpath.mk: classpath: 0.91 -> 0.93 |
| 23:40.09 | CIA-8 | 03bzhou * r4922 10optware/trunk/make/jamvm.mk: jamvm: 1.4.3 -> 1.4.4 |
| 23:48.29 | *** join/#nslu2-linux kfm82lin1k (n=kfm82@p54BEDA3A.dip.t-dialin.net) |
| 23:53.38 | chacko | Hi eno: I tried the manual boot strap and intial test, getting an error |
