| 00:00.03 | VoodooZ | plus apex does turn it off before booting the kernel. unless it's not?? |
| 00:00.23 | VoodooZ | That's ok. I'll try to do the testing for you. But I might need your input though. |
| 00:03.43 | *** join/#nslu2-linux ingeba (n=ingeba@109.80-203-45.nextgentel.com) |
| 00:09.36 | beewoolie | VoodooZ: OK. I've checked my jtag hardware again. It looks like it can run just fine at the speed of the parallel port. |
| 00:09.49 | beewoolie | It needs a pull-up on the nTRST line, but that seems to be the only issue. |
| 00:10.09 | beewoolie | In other words, if you are looking for a really cheap JTAG solution, that one can work. |
| 00:11.38 | AwayNAiL | how cheap is cheap? :) |
| 00:11.53 | beewoolie | The parts were about $5. |
| 00:12.08 | rwhitby | unslung-image now builds again ... |
| 00:15.35 | beewoolie | AwayNAiL: http://wiki.buici.com/twiki/bin/view/Main/SimpleJTAG |
| 00:17.20 | AwayNAiL | cool |
| 00:17.20 | AwayNAiL | thanks |
| 00:21.15 | beewoolie | AwayNAiL: if you have a problem reading the page or the site, let me know. I think I've got something borked in the apache setup, but I haven't figured it out, yet. |
| 00:22.59 | AwayNAiL | looked ok here |
| 00:23.36 | AwayNAiL | back later |
| 01:13.54 | tbm | jbowler-away: load -r -b 0x01000000 jffs2.image |
| 01:14.29 | tbm | jbowler-away: when I do this the kernel doesn't recognize it as a valid initrd |
| 01:14.34 | tbm | surely that should work, though |
| 01:26.56 | tbm | okay, I just tried the following: upslug2 -k kernel -r ./initramfs.gz |
| 01:27.07 | tbm | and initramfs.gz.swapped. neither worked. something seems to be wrong here |
| 01:36.18 | jbowler-away | I'm not sure that the upslug2 -r gets the byte swapping correct. Part of the problem is that it is loaded by RedBoot (like the kernel) |
| 01:36.50 | [g2] | tbm are you running BE or LE ? |
| 01:37.00 | jbowler-away | LE |
| 01:37.08 | jbowler-away | This is the Debian kernel |
| 01:37.35 | [g2] | jbowler-away I've built the Loft kernel LE and Redboot BE |
| 01:37.59 | [g2] | I think Redboot may actually be building a LE image and byteswapping it to BE |
| 01:38.16 | tbm | I just tried BE with straight 2.6.15 |
| 01:38.19 | jbowler-away | Loft kernel LE should be fine |
| 01:38.26 | tbm | again it says |
| 01:38.26 | tbm | checking if image is initramfs...it isn't (bad gzip magic numbers); looks like an initrd |
| 01:38.33 | tbm | and then: |
| 01:38.34 | tbm | RAMDISK: Compressed image found at block 0 |
| 01:38.34 | tbm | Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(1,0) |
| 01:38.35 | jbowler-away | RedBoot LE builds an LE RedBoot image - it has to. |
| 01:38.36 | [g2] | jbowler-away I need to have Redboot bot the box in LE |
| 01:39.02 | [g2] | So I can ship the Debian ARM LE Loft box to the UK for the Debian devs |
| 01:39.20 | jbowler-away | That's fine. Let me test it with slugos-ltu |
| 01:39.59 | jbowler-away | ... well, in a bit ... |
| 01:41.36 | tbm | ok, I think I tried every combination |
| 01:41.38 | tbm | be, le kernel |
| 01:41.44 | tbm | debian kernel, straight 2.6.15 |
| 01:41.52 | tbm | swapped and non-swapped initrd |
| 01:42.16 | tbm | initramfs doesn't boot, ext2 (plus kernel with ext2 built in) doesn't boot |
| 01:42.25 | tbm | a cramfs initrd boots though |
| 01:42.38 | tbm | it would be nice if someone could try if they can boot an initramfs |
| 01:43.35 | tbm | night |
| 01:56.23 | *** join/#nslu2-linux `skyhawk (n=anon@c-24-22-220-227.hsd1.wa.comcast.net) |
| 01:56.38 | `skyhawk | Hello all! |
| 01:56.48 | `skyhawk | i got a very important question concering unslug 5.5 and php and apache and php module... is there anyway to get gallery and the dam config.php page to work with this config and software? i tried everything i could come up with as a novice linux user.. no luck. tried thttpd+php didnt work either, couldnt get cherokee to work properly either am i out of luck? |
| 01:57.03 | `skyhawk | what configuration does work so i can run gallery and the config.php page? |
| 01:57.19 | [g2] | tbm I can try BE |
| 01:58.32 | tbm | that'd be great |
| 01:58.52 | [g2] | initramfs is on my list of things todo anyway |
| 01:59.49 | [g2] | tbm you are loading at 0x1d ? |
| 01:59.56 | tbm | yes |
| 02:00.08 | [g2] | how big is your initramfs ? :) |
| 02:00.12 | `skyhawk | any help please? |
| 02:00.15 | tbm | smaller than 10 megs |
| 02:00.30 | [g2] | It's gotta be smaller than 3 I think :) |
| 02:00.42 | [g2] | 0x20 == 32MB right ? |
| 02:01.35 | [g2] | tbm so I think you load is wrapping in memory |
| 02:01.42 | [g2] | and trashing the low part of memoy |
| 02:01.48 | [g2] | s/memoy/memory |
| 02:02.17 | tbm | it's smaller than 3 megs too |
| 02:02.30 | [g2] | well actually 2 |
| 02:02.41 | [g2] | 1d + 1 for the kernel= 1E |
| 02:02.49 | [g2] | so E and F are left |
| 02:02.59 | [g2] | is it smaller than 2 ? |
| 02:03.11 | tbm | the cramfs is almost 3 megs and loads fine. the initramfs is ~1 meg and doesn't |
| 02:04.17 | [g2] | you'll have to watch the cramfs as anything > 2MB may have issues |
| 02:04.35 | [g2] | tbm THX for the input |
| 02:04.53 | [g2] | sounds like size _isn't_ an issue with initramfs |
| 02:05.06 | tbm | yeah |
| 02:05.49 | [g2] | tbm you initrd ext2 does work right ? |
| 02:06.10 | tbm | no |
| 02:06.20 | tbm | ext2, jffs2 and initramfs don't work |
| 02:06.22 | tbm | cramfs does |
| 02:07.34 | [g2] | tbm I don't thing jffs2 _should_ work as initramfs |
| 02:07.43 | [g2] | jffs2 has to be a mtd device |
| 02:07.48 | [g2] | right ? |
| 02:08.30 | tbm | I don't know. But ext2 definitely should work and doesn't; same for initramfs |
| 02:08.53 | tbm | maybe I'm getting something obvious wrong; but I cannot see what and think it may be a bug |
| 02:11.46 | [g2] | tbm fully agree on the ext2 |
| 02:12.28 | [g2] | tbm does ext2 work as an initrd ? |
| 02:13.09 | tbm | normally, yes. not on the slug |
| 02:13.59 | [g2] | tbm you are using the bork Redboot on the slug |
| 02:14.16 | [g2] | and you've built the cmdline into the kernel you are loading right ? |
| 02:15.39 | [g2] | tbm is the ext2 roofs for 2.6.15 ? |
| 02:15.46 | tbm | yes, root=/dev/ram initrd=0x01000000,10M |
| 02:15.58 | tbm | it cannot even mount the ext2 so this doesn't matter |
| 02:16.02 | tbm | and yes redboot from the slug |
| 02:16.09 | tbm | anyway, gotta sleep now |
| 02:16.21 | [g2] | tbm ok... could you e-mail me the initrd ? |
| 02:16.35 | [g2] | I should be able to load it and boot to it on my Loft |
| 02:16.42 | [g2] | as it's just a rootfs |
| 02:17.27 | [g2] | sweet dreams |
| 02:17.36 | tbm | for initramfs just do 'find . | cpio --quiet -o -H newc > gzip -9c > initramfs.cpio.gz |
| 02:18.00 | tbm | it doesn't really matter what it contains since it cannot actually mount/detect it |
| 02:18.15 | tbm | the initrd I have here is LE |
| 02:18.21 | [g2] | ah ok |
| 02:18.35 | [g2] | but I could byte swap it |
| 02:18.54 | [g2] | anyway sweet dreams THX for all your great work |
| 02:24.01 | beewoolie | [g2]: Hey man |
| 02:28.16 | [g2] | beewoolie ! |
| 02:37.12 | beewoolie | [g2]: Guess what. That JTAG board that I build is perfectly fine. I thought it was broken all this time. |
| 02:37.55 | [g2] | beewoolie awesome |
| 03:34.42 | rwhitby | current unslung build boots |
| 03:35.50 | *** join/#nslu2-linux EvilDevil (n=ps@p54A6F18F.dip.t-dialin.net) |
| 03:54.20 | *** join/#nslu2-linux drif_ (n=drif@82-203-145-25.dsl.gohome.fi) |
| 04:21.28 | *** join/#nslu2-linux jipi (n=jipi@cm3.gamma180.maxonline.com.sg) |
| 05:07.27 | *** join/#nslu2-linux EvilDevil_ (n=ps@p54A6EDA2.dip.t-dialin.net) |
| 05:30.19 | CIA-5 | 03bzhou * 10unslung/ (4 files in 3 dirs): ruby cross ready, upgrade from 1.8.3 to 1.8.4 |
| 05:32.47 | *** join/#nslu2-linux ByronT (n=byron-po@adsl-068-209-197-246.sip.bhm.bellsouth.net) |
| 06:12.48 | jacques | testing |
| 06:13.01 | EvilDevil_ | testing failed |
| 06:13.07 | jacques | s/est/estest/ |
| 06:13.11 | jacques | :-) |
| 06:13.25 | jacques | this is wrong |
| 06:13.37 | jacques | s/wrong/what I meant/ |
| 06:13.48 | jacques | cool, ibot has a new trick |
| 06:14.14 | jacques | rather in this channel, jbot |
| 06:14.24 | jacques | jbot, botsnack |
| 06:14.25 | jbot | thanks, jacques |
| 06:19.05 | jacques | jbot, pi |
| 06:19.10 | jbot | pi is, like, 3.141592653589793238462643383279502884197169399375105820974944592307816406286208998628034825342117067982148086513282306647093844609550582231725359408128481117450284102701938521105559644622948954930381964428810975665933446128475648233786783165271201909145648566923460348610454326648213393607260249141273724587006606315588174881520920962829254091 |
| 06:19.24 | jacques | yeah, OK |
| 06:33.05 | *** join/#nslu2-linux ecopperbe (n=copperbe@82-40-186-72.cable.ubr04.newm.blueyonder.co.uk) |
| 06:36.36 | *** join/#nslu2-linux Eiffel (n=x@p548695C4.dip0.t-ipconnect.de) [NETSPLIT VICTIM] |
| 06:36.37 | *** join/#nslu2-linux jipi (n=jipi@cm3.gamma180.maxonline.com.sg) [NETSPLIT VICTIM] |
| 06:36.37 | *** join/#nslu2-linux cpage (n=cpage@netblock-68-183-40-90.dslextreme.com) |
| 06:36.37 | *** join/#nslu2-linux Jacmet (n=jacmet@50C59F0E.flatrate.dk) [NETSPLIT VICTIM] |
| 06:36.37 | *** join/#nslu2-linux dwery-away (n=dwery@nslu2-linux/dwery) |
| 06:36.37 | *** join/#nslu2-linux oleo (n=leon@193.2.111.14) [NETSPLIT VICTIM] |
| 06:36.37 | *** join/#nslu2-linux ByronT-Log (n=ByronT@nslu2-linux/ByronT) [NETSPLIT VICTIM] |
| 06:36.37 | *** join/#nslu2-linux copperbeech (n=copperbe@82.40.186.72) |
| 06:36.40 | *** join/#nslu2-linux ecopperbe (n=copperbe@82-40-186-72.cable.ubr04.newm.blueyonder.co.uk) |
| 06:44.00 | *** join/#nslu2-linux jipi (n=jipi@cm3.gamma180.maxonline.com.sg) |
| 06:44.00 | *** join/#nslu2-linux cpage (n=cpage@netblock-68-183-40-90.dslextreme.com) |
| 06:44.00 | *** join/#nslu2-linux Jacmet (n=jacmet@50C59F0E.flatrate.dk) [NETSPLIT VICTIM] |
| 06:44.00 | *** join/#nslu2-linux dwery-away (n=dwery@nslu2-linux/dwery) |
| 06:44.01 | *** join/#nslu2-linux oleo (n=leon@193.2.111.14) [NETSPLIT VICTIM] |
| 06:44.01 | *** join/#nslu2-linux ByronT-Log (n=ByronT@nslu2-linux/ByronT) [NETSPLIT VICTIM] |
| 06:55.42 | *** join/#nslu2-linux eno__ (n=eno@adsl-70-137-154-152.dsl.snfc21.sbcglobal.net) |
| 07:00.45 | *** join/#nslu2-linux ByronT-Log (n=ByronT@nslu2-linux/ByronT) |
| 07:29.06 | *** join/#nslu2-linux DrZimmerman (n=theo@84-72-180-35.dclient.hispeed.ch) |
| 08:57.18 | *** join/#nslu2-linux eumel (n=chatzill@p54831BA2.dip0.t-ipconnect.de) |
| 08:59.46 | *** part/#nslu2-linux EvilDevil (n=ps@p54A6EDA2.dip.t-dialin.net) |
| 10:14.44 | *** join/#nslu2-linux eFfeM (n=somebody@ip545787f8.direct-adsl.nl) |
| 10:22.03 | *** part/#nslu2-linux eumel (n=chatzill@p54831BA2.dip0.t-ipconnect.de) |
| 11:27.20 | *** join/#nslu2-linux Eiffel (n=x@p548695C4.dip0.t-ipconnect.de) |
| 11:35.39 | *** join/#nslu2-linux Eiffel_ (n=x@p5486B76E.dip0.t-ipconnect.de) |
| 12:13.47 | *** join/#nslu2-linux macsat (n=macsat@0x535b9779.arcnxx9.adsl-dhcp.tele.dk) |
| 13:13.27 | *** join/#nslu2-linux AdamBaker (n=aab@userch028.dsl.pipex.com) |
| 13:48.59 | *** join/#nslu2-linux emm_is (n=chatzill@i-83-67-201-219.freedom2surf.net) |
| 13:54.59 | *** join/#nslu2-linux macsat (n=macsat@0x535b9779.arcnxx9.adsl-dhcp.tele.dk) |
| 14:21.26 | *** join/#nslu2-linux macsat (n=macsat@0x535b9779.arcnxx9.adsl-dhcp.tele.dk) |
| 14:33.27 | *** join/#nslu2-linux eFfeM (n=slug@ip545787f8.direct-adsl.nl) |
| 14:35.12 | eFfeM | jbowler-zzz, reading my log: I assumed that for installing os modules I needed ipkg (as these are .ipk files), and they need to come from the kernel build (at least that is my understanding) |
| 15:32.12 | *** join/#nslu2-linux macsat (n=macsat@0x535b9779.arcnxx9.adsl-dhcp.tele.dk) |
| 16:09.11 | *** join/#nslu2-linux malfi (n=malte@dslb-084-059-004-015.pools.arcor-ip.net) |
| 16:12.19 | *** join/#nslu2-linux eFfeM-log (n=eFfeM@ip545787f8.direct-adsl.nl) |
| 16:12.40 | *** join/#nslu2-linux neotheone (n=neo@ppp-82-135-73-91.mnet-online.de) |
| 16:13.08 | *** join/#nslu2-linux geojeff (n=geojeff@66.112.110.134.dyn.centurytel.net) |
| 16:42.52 | *** join/#nslu2-linux EvilDevil (n=ps@p54A6EDA2.dip.t-dialin.net) |
| 16:48.23 | *** join/#nslu2-linux ByronT (n=byron-po@nslu2-linux/ByronT) |
| 17:23.33 | eFfeM | jbowler-zzz, meanwhile koen in #openslug enlightened me that dpkg could also install ipk files. Added a note to the wiki to that extent |
| 17:51.32 | *** join/#nslu2-linux eFfeM (n=slug@ip545787f8.direct-adsl.nl) |
| 18:18.21 | *** join/#nslu2-linux eFfeM-log (n=eFfeM@ip545787f8.direct-adsl.nl) |
| 18:21.34 | *** join/#nslu2-linux neotheone (n=neo@host-82-135-95-247.customer.m-online.net) |
| 18:27.14 | *** join/#nslu2-linux eFfeM-log (n=eFfeM@ip545787f8.direct-adsl.nl) |
| 18:32.04 | *** join/#nslu2-linux eFfeM-log (n=eFfeM@ip545787f8.direct-adsl.nl) |
| 18:57.37 | *** join/#nslu2-linux eovermeer (n=eovermee@cn-pij-cb01-1019.dial.kabelfoon.nl) |
| 18:58.35 | *** join/#nslu2-linux eFfeM-log (n=eFfeM@ip545787f8.direct-adsl.nl) |
| 19:04.49 | *** join/#nslu2-linux caplink811 (n=Joerg@dslb-084-059-091-195.pools.arcor-ip.net) |
| 19:05.51 | *** join/#nslu2-linux caplink811-log (n=caplink8@dslb-084-059-091-195.pools.arcor-ip.net) |
| 19:17.32 | *** join/#nslu2-linux newserver (n=Anders@port20.ds1-aboes.adsl.cybercity.dk) |
| 19:19.04 | newserver | i have a problem with kernel-module-rfcomm. it seems it need to be compiled with CONFIG_BLUEZ_RFCOMM_TTY=y instead of =m. My nOOb question is: do I have to build the entire kernel? |
| 19:19.22 | neotheone | hah nslu2-german |
| 19:19.22 | neotheone | <caplink811> flashen immer ohne |
| 19:19.24 | neotheone | sorry |
| 19:47.50 | *** join/#nslu2-linux SkySurfer (n=SkySurfe@p549E1094.dip0.t-ipconnect.de) |
| 19:48.03 | SkySurfer | hi |
| 19:48.55 | SkySurfer | anyone here who can help me with a package building problem |
| 19:49.11 | SkySurfer | ? |
| 19:49.36 | caplink811 | morning, maybe, just ask, or better, describe your problem |
| 19:49.57 | SkySurfer | i try building a mldonkey package |
| 19:50.20 | SkySurfer | mldonkey depends on ocaml and ncurses |
| 19:50.59 | SkySurfer | i build both and included them in my make file with ocaml-stage ncurses-stage |
| 19:51.15 | SkySurfer | but wenn i try to compile it i get the folowing error |
| 19:52.52 | *** part/#nslu2-linux SkySurfer (n=SkySurfe@p549E1094.dip0.t-ipconnect.de) |
| 19:53.05 | *** join/#nslu2-linux SkySurfer (n=SkySurfe@p549E1094.dip0.t-ipconnect.de) |
| 19:53.25 | SkySurfer | cannot find -lcurses |
| 19:55.41 | SkySurfer | where should curses be installed ? |
| 19:56.40 | caplink811 | haven't any hint, that can help you, excepting, stay some hours in that channel, anyone may read the logs, and have an solution |
| 19:57.11 | SkySurfer | ok i stay in |
| 20:00.14 | emm_is | syksurfer - are you native building or cross-compiling? |
| 20:00.35 | SkySurfer | cross-compiling |
| 20:00.53 | emm_is | unslung or openslug |
| 20:01.00 | SkySurfer | unslung |
| 20:01.11 | emm_is | mastermakefile? |
| 20:01.42 | SkySurfer | sorry what do mean with it ? |
| 20:03.02 | emm_is | are you using monotone/bitbake or the old AddAPackageToUnslung howto? |
| 20:03.47 | SkySurfer | AddAPackageToUnslung |
| 20:06.28 | *** join/#nslu2-linux bullet (n=bullet@66.59.62.81.cust.bluewin.ch) |
| 20:06.47 | emm_is | well, if I remember correctly, you need to add a dependance to ncurses in your makefile for your target package. It is a bit of a pain but consult another makefile of an application that depends on curses (hmm, nano maybe or ctorrent) and see what they do. It isn't complicated but does need some tiral and error |
| 20:07.31 | SkySurfer | ok i have a lool |
| 20:07.37 | SkySurfer | look |
| 20:20.39 | *** join/#nslu2-linux VoodooZ (n=VoodooZ@CPE00c0f021712c-CM000f9fac823a.cpe.net.cable.rogers.com) |
| 20:24.50 | SkySurfer | i added MLDONKEY_CPPFLAGS=-I$(STAGING_PREFIX)/include/ncurses |
| 20:24.50 | SkySurfer | MLDONKEY_LDFLAGS=-I$(STAGING_PREFIX)/include/ncurses but it shows non effect |
| 20:34.42 | emm_is | I recall you also need to list ncurses in an enviromental variable set in the makefile listing all the package dependances |
| 20:35.07 | emm_is | Search arround in an example |
| 20:36.39 | *** join/#nslu2-linux stanmade (n=kfm82@p54BEF856.dip.t-dialin.net) |
| 20:39.31 | SkySurfer | i searched all makefiles for ncurses phrases and added also the path to it to $PATH but no effect |
| 20:40.31 | *** part/#nslu2-linux SkySurfer (n=SkySurfe@p549E1094.dip0.t-ipconnect.de) |
| 20:40.38 | *** join/#nslu2-linux SkySurfer (n=SkySurfe@p549E1094.dip0.t-ipconnect.de) |
| 20:47.32 | *** join/#nslu2-linux marceln (n=marceln@pion.xs4all.nl) |
| 20:58.23 | emm_is | skysurfer -- no, there is a variable where you list packages your package depends on |
| 20:59.09 | emm_is | look at wget, that depends on several libs |
| 20:59.28 | SkySurfer | MLDONKEY_DEPENDS=ncurses |
| 21:00.42 | emm_is | looks good |
| 21:00.44 | emm_is | ! |
| 21:00.49 | SkySurfer | i think so |
| 21:01.35 | *** join/#nslu2-linux rwhitby-away (n=rwhitby@nslu2-linux/rwhitby) |
| 21:01.43 | SkySurfer | i tried to copy past the complete output but my client don't post it |
| 21:08.01 | AdamBaker | SkySurfer: your message said MLDONKEY_LDFLAGS=-I$(STAGING_PREFIX)/include did you really put that in the .mk or did you use -L$(STAGING_PREFIX)/lib |
| 21:08.47 | SkySurfer | it's an I |
| 21:09.15 | SkySurfer | should it be -L$(STAGING_PREFIX)/lib ? |
| 21:09.16 | AdamBaker | Skysurfer: Even better would be to use $(STAGING_LDFLAGS) for MLDONKEY_LDFLAGS |
| 21:09.45 | AdamBaker | -L specifies library dirs, -I is for include dirs |
| 21:15.32 | SkySurfer | i added $(STAGING_LDFLAGS) and also -L$(STAGING_PREFIX)/lib but no effect |
| 21:26.06 | AdamBaker | From the top of your optware build tree type "ls staging/opt/lib/libcurses.*" to see if you have successfully staged curses and the link is failing to find it or if you have failed to stage it |
| 21:28.21 | SkySurfer | it don't find any file |
| 21:30.30 | AdamBaker | Have you remembered to include "$(MAKE) ncurses-stage" in your .configured rule |
| 21:30.48 | SkySurfer | yes it's in |
| 21:32.21 | AdamBaker | Ah - The ncurses lib is called libncurses, not libcurses |
| 21:32.36 | AdamBaker | change the -lcurses to -lncurses |
| 21:33.50 | eno-away | SkySurfer, AFAIK optware ocaml is not cross built yet |
| 21:34.51 | SkySurfer | i crosscompiled it and it outputed the ocamlc.opt and so on |
| 21:37.44 | eno-away | cool, as a while ago i worked on native 3.08.03 |
| 21:38.07 | eno-away | did you need to make any change to make it cross compilable? |
| 21:39.57 | SkySurfer | i only changed to the newer version 3.09.1 |
| 21:42.22 | eno | that's really good news, off to cross build the new ocaml ... |
| 21:43.28 | SkySurfer | if build the ipkg package already but it still untested |
| 21:44.24 | eno | i c, that's a very good start already |
| 21:45.21 | eno | the real test is unison and mldonkey |
| 21:45.48 | SkySurfer | i hope i get mldonkey compiled ;) |
| 21:46.52 | eno | AdamBaker gave you the right instruction, does it still complain about ncurses? |
| 21:48.45 | SkySurfer | the problem is that i have to change the mldonkey makefile that gets extracted from the source.tar.bz2 so how can i do this ? |
| 21:48.48 | SkySurfer | patch ? |
| 21:51.40 | AdamBaker | yep |
| 21:54.15 | eno | diff -u makefile.orig makefile > .../sources/mldonkey/makefile.patch |
| 21:54.16 | eno | then add it to MLDONKEY_PATCHES |
| 21:54.16 | SkySurfer | thx |
| 21:57.36 | eno | something's wrong with the cross built ocaml, |
| 21:57.39 | eno | $ file builds/ocaml-3.09.1-ipk/opt/bin/ocamlrun |
| 21:57.40 | eno | builds/ocaml-3.09.1-ipk/opt/bin/ocamlrun: ELF 32-bit LSB executable, Intel 80386, version 1 (SYSV), for GNU/Linux 2.2.0, dynamically linked (uses shared libs), not stripped |
| 22:07.48 | SkySurfer | i can't find this -lcurse anywehre |
| 22:08.44 | eno | $ ls staging/opt/lib/libncurses* |
| 22:08.46 | eno | staging/opt/lib/libncurses.a staging/opt/lib/libncurses_g.a staging/opt/lib/libncurses.so staging/opt/lib/libncurses.so.5 staging/opt/lib/libncurses.so.5.5 |
| 22:09.44 | eno | SkySurfer, i think the bigger problem ahead is ocaml |
| 22:10.09 | eno | can you do a "file builds/ocaml-3.09.1-ipk/opt/bin/ocamlrun"? |
| 22:12.19 | SkySurfer | builds/ocaml-3.09.1-ipk/opt/bin/ocamlrun: ELF 32-bit LSB executable, no machine, version 1 (SYSV), for GNU/Linux 2.2.0, dynamically linked (uses shared libs), stripped |
| 22:14.02 | eno | i'm a bit confused, what does "no machine" mean? |
| 22:14.41 | SkySurfer | yes a bit |
| 22:14.53 | eno | anyway, launching a native ocaml compilation |
| 22:15.13 | SkySurfer | configure told me something little em... ? |
| 22:16.26 | SkySurfer | should i try to copy the ocamlrun to the router and try to run mlnet.byte ? |
| 22:17.10 | eno | are u using wl500g or nslu2? |
| 22:17.28 | SkySurfer | wl500gx |
| 22:18.16 | eno | yes, definitely try "ipkg install" your shining new ipk |
| 22:18.47 | eno | so the difference could be due to wiley & slug |
| 22:19.57 | SkySurfer | how can i geht the ipkg installed on the router ? where do i have to upload the package ? |
| 22:20.57 | eno | just scp (ftp, or wget or whatever) the ipk file over, then on wl500gx, run "ipkg install pkg-xxxx.ipk" |
| 22:21.19 | SkySurfer | ok |
| 22:35.59 | SkySurfer | Fatal error: unknown C primitive `unix_dup' |
| 22:36.03 | SkySurfer | seams not to worl |
| 22:36.07 | SkySurfer | work |
| 22:39.25 | eno | my guess is that unix_dup is available on your cross host but not on the wl500gx |
| 22:40.16 | eno | if there is a way to tell it not to use 'unix_dup' |
| 22:43.47 | SkySurfer | i don't know if there is a way |
| 22:44.28 | *** join/#nslu2-linux rwhitby (n=c058a723@nslu2-linux/rwhitby) |
| 22:50.31 | SkySurfer | how about ? |
| 22:50.39 | SkySurfer | ups /opt/bin/ocamlrun: 1: Syntax error: "(" unexpected |
| 22:50.46 | AdamBaker | unix_dup is a kernel function which should be present in any kernel which implements unix domain sockets. It is possible the uclibc (as used on the wl500g) doesn't include a C wrapper for that system call. It may be easier to write the wrapper than work round it's absence |
| 22:51.49 | SkySurfer | the unix_dup was my fault .. it was the output from the wrong mashine |
| 22:52.06 | SkySurfer | the syntax error is from the router |
| 22:52.24 | SkySurfer | maybe an error in the bytecode ? |
| 23:16.14 | *** join/#nslu2-linux emm_is (n=chatzill@i-83-67-201-219.freedom2surf.net) |