| 00:00.14 | pH5 | wgpio just gives you a list of the gpios that change during the running time. that's the interesting result. no need to compare |
| 00:03.56 | renatostore | so i have to silence gipios one by one ? |
| 00:05.55 | pH5 | renatostore: yes. in this case it is better to make a script. |
| 00:20.37 | renatostore | GPLR 10, 36, 108 |
| 00:23.25 | pH5 | nice. gpio 10 and 108 are both input, probably from the gsm chip. it is exactly the same on the magician |
| 00:23.34 | pH5 | anything else? |
| 00:24.16 | pH5 | did you compare "dump gpio" with flight mode on and off? |
| 00:34.04 | renatostore | dump gpio changes: 10, 31, 36, 42-45, 58-60, 69, 108, 72, 76, 77 |
| 00:38.43 | renatostore | pH5: are you there? |
| 00:38.53 | pH5 | hm. I looked at the wiki page |
| 00:39.43 | renatostore | all tests in a zone bad covered by operators |
| 00:39.57 | pH5 | 31 is I2S_SYNC, 36 is FFUART, 42-45 are BTUART, 58-73 are LCD pins and 76,77 are LCD gpios too |
| 00:40.11 | pH5 | renatostore: that is no problem |
| 00:40.35 | pH5 | so there is no unknown gpio output pin that changes level. |
| 00:41.03 | renatostore | 10, 36, 108 |
| 00:41.07 | renatostore | only |
| 00:41.11 | pH5 | I assume that gsm power is handled by EGPIOs on the cpld |
| 00:41.15 | pH5 | 10 and 108 are inputs |
| 00:41.55 | pH5 | 36 is also an input, I think FFUART_DCD |
| 00:43.48 | pH5 | I think that gpio 10 is used as an interrupt to wake up the cpu when there is an incoming call, but that doesn't work yet on the magician |
| 00:45.55 | *** join/#htc-linux BobOfDoom (i=ato@2002:3d45:1873:0:0:0:0:1) |
| 00:47.41 | renatostore | what now? |
| 00:48.37 | renatostore | can i close haret? |
| 00:51.01 | pH5 | renatostore: the next step would be to do the "wi" trace of the cpld registers at 0xa9500000 with haret |
| 00:51.32 | renatostore | how? |
| 00:53.00 | Kevin2 | Hi |
| 00:53.00 | pH5 | first "set trace 0xa9500000" and "set tracemask 0xff" to tell haret to trace all memory accesses to 0xa95000xx |
| 00:53.06 | pH5 | hi Kevin2 |
| 00:54.13 | Kevin2 | Hi pH5 |
| 00:55.17 | pH5 | renatostore: then run "wi 1" and watch many irqs scroll by. set haret to ignore them with "set ii <num> 1" and then run "wi 20" and turn off the phone. |
| 01:00.07 | Kevin2 | What device are you guys working on? |
| 01:00.36 | pH5 | renatostore has got an alpine, which is supposed to be similar to the magician. |
| 01:03.24 | Kevin2 | Cool. |
| 01:03.30 | Kevin2 | Seems like a lot of interest in Hermes recently. |
| 01:05.36 | pH5 | but there are still problems at the haret level as I understand? |
| 01:05.58 | pH5 | It took me over three months to get at least some sound out of the magician's codec. Now I managed to get the phone running in two days. And I don't even need the codec to do voice calls. |
| 01:09.33 | Kevin2 | Heh, I spent nearly a month just figuring out that USB host dma was on. (Worse, it was fixed in other people's code already.) Yeah, I bet I could port a new phone pretty quick now. |
| 01:09.57 | renatostore | next time ... good night |
| 01:10.51 | Kevin2 | I don't know of any Hermes haret problems. (But that isn't to say there aren't any.) Full support for things like "wi" aren't there of course. But to the best of my knowledge it is probably kernel problems stopping the boot. |
| 01:18.48 | pH5 | Oh, good. I thought that there were still DMA problems. |
| 01:18.56 | pH5 | gotta go now, too. |
| 01:18.58 | pH5 | good night |
| 01:39.08 | *** join/#htc-linux Hawk|- (n=Hawk@p57A54735.dip0.t-ipconnect.de) |
| 01:47.12 | *** join/#htc-linux phongred (n=phongred@203.113.144.83) |
| 01:57.12 | phongred | hi all |
| 02:48.35 | *** join/#htc-linux Ralith (n=ralith@soggy202.drizzle.com) |
| 03:30.53 | oppiz | hey |
| 03:30.57 | *** part/#htc-linux WizMaui (n=WizMaui@62.112.90.231) |
| 03:36.25 | oppiz | Kevin2? you around? |
| 03:38.00 | Ralith | So I'm gunna be receiving a Universal within the next four or five days, and I'd like to help with the project. I'm relatively inexperienced as far as coding goes, and have absolutely no kernel hacking experience, but am relatively fluent in Linux (shell, configuration, etc). What can i do? |
| 03:50.42 | *** join/#htc-linux silven (n=zmc@adsl-72-50-76-164.prtc.net) |
| 03:51.02 | silven | Quick question: What cpu does the magician run? |
| 03:57.33 | silven | nvm - found it. pxa |
| 04:11.05 | phongred | can u help me use linux in HTC O2s (BlueAngel) phone |
| 04:11.52 | silven | phongred: Is linux installed? |
| 04:13.54 | phongred | yes |
| 04:14.07 | phongred | HTC phone O2s |
| 04:14.28 | silven | Great, so what do you need help with.. perhaps it's gpe/opie related matter. |
| 04:15.05 | phongred | yes opie |
| 04:18.04 | phongred | i'm using WinDowsMobile 2005 |
| 04:22.47 | *** part/#htc-linux silven (n=zmc@adsl-72-50-76-164.prtc.net) |
| 04:57.12 | *** join/#htc-linux VisN (n=VisualN@ip227.131.adsl.wplus.ru) |
| 07:04.01 | *** join/#htc-linux asylumed (n=insanity@196.211.116.2) |
| 07:15.50 | *** join/#htc-linux rejon (n=rejon@c-67-174-202-239.hsd1.ca.comcast.net) |
| 07:16.13 | *** part/#htc-linux rejon (n=rejon@c-67-174-202-239.hsd1.ca.comcast.net) |
| 07:31.21 | *** join/#htc-linux goxboxlive (n=goxboxli@9.80-202-160.nextgentel.com) |
| 07:42.34 | *** join/#htc-linux Ralith (n=ralith@soggy202.drizzle.com) |
| 07:44.45 | *** join/#htc-linux Ralith (n=ralith@soggy202.drizzle.com) |
| 07:58.31 | *** join/#htc-linux phongred (n=phongred@203.113.144.83) |
| 08:27.11 | *** join/#htc-linux psokolovsky_ (n=psokolov@238.usernat.ip.net.ua) |
| 08:44.15 | *** join/#htc-linux RoEn_PC (n=roen@p54A67C5B.dip.t-dialin.net) |
| 09:19.14 | *** join/#htc-linux pH5 (n=ph5@e178255048.adsl.alicedsl.de) |
| 09:23.44 | kimuSan^ | morning |
| 09:25.45 | kimuSan^ | cr2: whan you say that the USBH is enabled, is that then in the hardware or is it enabled to use. |
| 09:28.04 | pH5 | good morning |
| 09:28.10 | goxboxlive | morning |
| 09:42.12 | maniacxs | good morning |
| 09:43.54 | maniacxs | gomunicator crashes :( |
| 09:45.44 | maniacxs | any ideas? http://pastebin.ca/307805 |
| 09:51.19 | goxboxlive | maniacxs there? |
| 09:51.33 | maniacxs | hi goxboxlive ;) |
| 09:51.44 | goxboxlive | hi |
| 09:52.03 | goxboxlive | your dbus/system.conf file is failing |
| 09:52.18 | goxboxlive | if you replece it with this it should work: |
| 09:52.49 | goxboxlive | http://pastebin.ca/307809 |
| 09:53.33 | goxboxlive | Find the file system.conf, i mean it is somewhere in /etc/dbus-1 or something |
| 09:53.40 | maniacxs | i found it |
| 09:53.45 | goxboxlive | good |
| 09:53.53 | maniacxs | was away to get a cup of coffee ;) |
| 09:53.55 | goxboxlive | make a copy of it and make a new one |
| 09:54.00 | goxboxlive | :-) |
| 09:54.15 | goxboxlive | with the content in pastebin |
| 09:54.34 | goxboxlive | restart dbus /etc/init.d/dbus restart |
| 09:54.49 | goxboxlive | and then try to launch gomunicator |
| 09:57.10 | maniacxs | uh ... no start-stop-daemon ? |
| 09:57.28 | maniacxs | goxboxlive: dou you know in which package it is? |
| 09:58.06 | goxboxlive | then first /etc/init.d/dbus stop |
| 09:58.12 | goxboxlive | and the /etc/init.d/dbus start |
| 09:58.14 | goxboxlive | :-) |
| 09:58.17 | maniacxs | no chance |
| 09:58.35 | goxboxlive | What is not working? |
| 09:58.38 | maniacxs | stop needs it too and starting has not permission on pidfile |
| 09:58.51 | maniacxs | is there no start-stop-daemon? |
| 09:58.55 | maniacxs | in angstrom? |
| 09:59.02 | goxboxlive | It should be, it works with mine |
| 09:59.08 | goxboxlive | but just reboot then |
| 09:59.46 | maniacxs | ok i found the error |
| 10:00.01 | maniacxs | i have not finished my first coffee yet. |
| 10:00.04 | maniacxs | was not root |
| 10:00.08 | goxboxlive | :-) |
| 10:00.49 | maniacxs | :) asking me for a operator pin |
| 10:02.15 | maniacxs | ringing at home ;) |
| 10:02.19 | goxboxlive | :-) |
| 10:02.26 | goxboxlive | Did the pin code work? |
| 10:02.34 | maniacxs | does it stop ringing? |
| 10:02.41 | maniacxs | yes it worked |
| 10:02.58 | goxboxlive | sometimes the hangup works, wometimes it doesnt |
| 10:03.03 | maniacxs | no it does not stop ringing when |
| 10:03.22 | goxboxlive | I have never tried the pin code stuff. |
| 10:03.38 | maniacxs | never never use winmobile anymore ... |
| 10:03.42 | goxboxlive | Have you changed your theme so GPE looks bether? |
| 10:03.48 | maniacxs | no not yet |
| 10:09.50 | kimuSan^ | where has teh gpe screenshots gone? |
| 10:10.18 | *** join/#htc-linux maniacxs (n=maniacxs@pD95463C8.dip0.t-ipconnect.de) |
| 10:10.43 | goxboxlive | http://scap.linuxtogo.org/ |
| 10:14.54 | maniacxs | in gomunicator on the right side the "Operator 26201" is this the number for the operator? |
| 10:17.31 | pH5 | 26201 is D1-TELEKOM |
| 10:18.02 | maniacxs | what the hell! |
| 10:18.21 | pH5 | looks like for some reason operator selection is set to AT+COPS=3,2 (numeric) instead of AT+COPS=3,1 (alphanum. short) |
| 10:18.52 | maniacxs | the call was hangup and some guy told something about "... free of charge" |
| 10:22.29 | maniacxs | does the mic work? |
| 10:30.57 | goxboxlive | no |
| 10:31.33 | maniacxs | so that is why my girlfriend in the other room is not hearing me |
| 10:35.28 | maniacxs | goxboxlive: on the status page it says mic is working |
| 10:36.30 | pH5 | is the mic connected directly to the phone chip? on the magician I have to make sure to set up the input_select egpios correctly. enabling the mic from the phone chip side is somehow done by the at init string. |
| 10:37.56 | goxboxlive | maniacxs Yes the mic is working, but not with gomunicator. You all free to write some code for it if you want to. |
| 10:54.33 | *** join/#htc-linux rmoravcik (n=rmoravci@icm4-orange.orange.sk) |
| 10:55.01 | *** join/#htc-linux LunohoD_ (n=alex@e180115244.adsl.alicedsl.de) |
| 10:57.11 | *** join/#htc-linux rob_w (n=bob@p85.212.131.207.tisdip.tiscali.de) |
| 10:57.37 | rob_w | pH5, approved ;-) |
| 10:58.45 | maniacxs | goxboxlive: a note for the next image: the user that is created in gpe after first boot is not in dialout group |
| 10:58.48 | pH5 | rob_w: thanks |
| 10:59.29 | goxboxlive | maniacxs: I know that, that is why i am running as root so far. |
| 10:59.41 | pH5 | rob_w: what is the preferred channel for gomunicator discussion? #gpe? |
| 10:59.45 | rob_w | pH5, there are many changes still on the xanadux cvs which are not yet merged onto ltg .. |
| 10:59.57 | maniacxs | goxboxlive: is there something like bugtracking for your images? |
| 11:00.04 | rob_w | nothing prefferred yet |
| 11:00.26 | pH5 | ok |
| 11:01.29 | pH5 | I noticed that gomunicator doesn't handle unsolicited return codes very well. |
| 11:02.08 | pH5 | I sometimes have TCCSQ: service quality messages between AT+CPIN= and the corresponding OK, that always kills the gomunicator state machine |
| 11:02.11 | rob_w | well .. it is not yet very well grown .. i actually did not work on it for a long time |
| 11:03.10 | rob_w | pH5, in between ?? thats weired |
| 11:04.21 | pH5 | yup. this phone seems to send the %HTCCSQ and %SATI messages whenever it likes |
| 11:05.55 | goxboxlive | <maniacxs> No, not yet but you are free to add one at the hh.org wiki |
| 11:06.42 | rob_w | pH5, i think you will need to prevent that somehow .. it needs to obey US as MCU .. |
| 11:08.46 | pH5 | rob_w: I have no idea how :( the radio firmware is encrypted. I also have to improve / separate the processLine parser for magician, as only frames with 0x02,0x16...0x02 are at gsm. there are some trace messages with 0x02,0x12...0x02 and some control messages with 0x02,0x19...0x02 that have to be ignored by gomunicator |
| 11:09.25 | goxboxlive | Anyone know how i create a package-index manually, without bitbake? |
| 11:09.58 | pH5 | goxboxlive: ipkg-make-index |
| 11:11.43 | goxboxlive | ok, but i dont have ipkg* on my host machine. Wich package do i need to install in to debian? |
| 11:13.34 | pH5 | goxboxlive: I don't think it is packaged for debian. It's a python script in staging/i686-linux/bin (if your host is i686) |
| 11:13.47 | goxboxlive | Ph5 thx |
| 11:13.58 | *** join/#htc-linux Fossi (n=Fossi@e176111154.adsl.alicedsl.de) |
| 11:26.41 | *** join/#htc-linux BabelO (n=Fabrice@lun34-2-82-238-28-28.fbx.proxad.net) |
| 11:40.32 | *** join/#htc-linux tudenbart (n=willi@xdsl-213-196-251-120.netcologne.de) |
| 11:50.36 | *** join/#htc-linux maniacxs_ (n=maniacxs@pD9545FB9.dip0.t-ipconnect.de) |
| 12:00.40 | maniacxs_ | goxboxlive: i read some irclogs. is the universal mic problem when doing phone calls the same thing what pH5 has to do with the magician? |
| 12:28.31 | *** join/#htc-linux pH5 (n=ph5@e178255048.adsl.alicedsl.de) |
| 12:36.23 | *** join/#htc-linux pH5_ (n=ph5@e178255048.adsl.alicedsl.de) |
| 12:36.31 | goxboxlive | maniacxs: maybe, i dont know wich problems pH5 has with magician. |
| 12:39.59 | *** join/#htc-linux pleemans (n=peter@d51A5E612.access.telenet.be) |
| 13:45.49 | *** join/#htc-linux rmoravcik (n=rmoravci@icm4-orange.orange.sk) |
| 14:51.22 | *** join/#htc-linux goxboxlive (n=goxboxli@9.80-202-160.nextgentel.com) |
| 14:52.32 | goxboxlive | BabelO: a phone app. Great. |
| 14:58.40 | cr2 | goxboxlive: hi. i have added the asic3_leds driver. can you have a look ? |
| 15:00.39 | goxboxlive | cr2: i have allready tried it out |
| 15:01.27 | *** join/#htc-linux WizMaui (n=WizMaui@62.112.90.231) |
| 15:01.40 | goxboxlive | I noticed i had to also add leds support i the config. Could you make that default in the Kconfig? |
| 15:01.49 | goxboxlive | Like the hx4700 Kconfig? |
| 15:02.51 | WizMaui | can someone tell me what is necessary to build opie? |
| 15:03.07 | goxboxlive | Openembedded |
| 15:03.17 | WizMaui | hmmm |
| 15:03.37 | goxboxlive | http://www.openembedded.org/wiki/GettingStarted |
| 15:03.57 | WizMaui | can i adapt that for htc wizard eg. omap850 |
| 15:04.18 | goxboxlive | But, be aware of that it will take several of hours the first time |
| 15:04.41 | WizMaui | i will have a look at it |
| 15:04.45 | goxboxlive | Yes you can do that localy, but why dont you rather build OPieII |
| 15:04.56 | WizMaui | OPiell? |
| 15:05.00 | goxboxlive | You dont need OPenEmbedded for that |
| 15:05.12 | goxboxlive | http://opie.linuxtogo.org |
| 15:05.48 | goxboxlive | WizMaui: sorry: http://opie.home.linuxtogo.org/ |
| 15:06.19 | WizMaui | looks good |
| 15:06.23 | goxboxlive | cr2: They work, and the 3 leds(redblue and green) are listed in /sys/class/leds |
| 15:06.30 | *** join/#htc-linux rmoravcik (n=rmoravci@icm3-orange.orange.sk) |
| 15:06.46 | goxboxlive | cr2:Now we need the keyboad backlight led. |
| 15:07.27 | goxboxlive | WixMaui: Yes it looks good, but the source has been out less than a month now, so it is still buggy. |
| 15:07.41 | *** join/#htc-linux BobOfDoom (i=ato@2002:d20b:925d:0:0:0:0:1) |
| 15:07.43 | goxboxlive | s/WixMaui/WizMaui/ |
| 15:07.53 | WizMaui | ;) |
| 15:08.52 | goxboxlive | But, when OPieII reach OPenEmbedded i will recomend u to build with OE. Once your in to it it's very easy. |
| 15:09.34 | goxboxlive | You can also build GPE, Rootfs image and so on. Just by calling "bitbake gpe-image" |
| 15:10.14 | goxboxlive | It gives yuo a complete image, include kernel modules, busybox and a GUI envirement. |
| 15:10.43 | WizMaui | hmmm...all we got at the moment is a working framebuffer driver |
| 15:10.44 | WizMaui | http://webtomware.rhoen.de/linwizard |
| 15:10.54 | WizMaui | don't know if this is enough for opie ;) |
| 15:11.53 | cr2 | WizMaui: touchscreen ? |
| 15:12.12 | goxboxlive | You never know until you have tried :-) |
| 15:12.16 | cr2 | goxboxlive: does the wifi/bt led work too ? |
| 15:12.25 | WizMaui | i haven't testet it yet but webtom build a driver |
| 15:12.30 | cr2 | can you pastebin the .config diff ? |
| 15:12.31 | WizMaui | http://linwizard.sourceforge.net/index.php?option=com_joomlaboard&Itemid=3&func=view&id=74&catid=5 |
| 15:13.31 | cr2 | WizMaui: have you registered the MTYPEs for your phones ? afaik you use the typhoon ID, and it will make problems (sooner or later) with haret. |
| 15:13.46 | WizMaui | how can i register the mtype? |
| 15:18.09 | cr2 | http://www.arm.linux.org.uk/developer/machines/ |
| 15:18.29 | cr2 | goxboxlive: http://forum.xda-developers.com/showthread.php?t=286884&page=4 |
| 15:18.42 | cr2 | Don´t know if it has been mentioned here before, but HTC expects the Athena/HTC X7500 to sell for 1300 euros w/o contract. Pretty steep. |
| 15:22.01 | goxboxlive | cr2: Actually, i just booted the image with it included, i didnt ry wifi/bt. But i tried charging with AC power but that didnt work. |
| 15:22.42 | cr2 | the LED did not work, or charging ? |
| 15:23.16 | cr2 | and are you using the defconfig ? |
| 15:24.05 | cr2 | CONFIG_HTCUNIVERSAL_LEDS=y |
| 15:24.06 | goxboxlive | The led |
| 15:24.17 | cr2 | CONFIG_NEW_LEDS=y |
| 15:24.17 | cr2 | CONFIG_LEDS_CLASS=y |
| 15:24.27 | cr2 | CONFIG_LEDS_ASIC3=y |
| 15:24.31 | goxboxlive | cr2: Yno, not the defconfig, i edited the Kconfig file |
| 15:24.37 | cr2 | CONFIG_LEDS_TRIGGERS=y |
| 15:24.39 | goxboxlive | let me check |
| 15:24.47 | cr2 | CONFIG_LEDS_TRIGGER_TIMER_ASIC3=m |
| 15:25.13 | goxboxlive | CONFIG_HTCUNIVERSAL_LEDS=y |
| 15:25.18 | cr2 | diff -u .config arch/arm/configs/htcuniversal_defconfig |
| 15:25.52 | goxboxlive | CONFIG_HTCUNIVERSAL_LEDS=y |
| 15:25.52 | goxboxlive | # LED devices |
| 15:25.53 | goxboxlive | CONFIG_NEW_LEDS=y |
| 15:25.53 | goxboxlive | CONFIG_LEDS_CLASS=y |
| 15:25.53 | goxboxlive | # LED drivers |
| 15:25.53 | goxboxlive | CONFIG_LEDS_ASIC3=y |
| 15:25.55 | goxboxlive | # LED Triggers |
| 15:25.57 | goxboxlive | CONFIG_LEDS_TRIGGERS=y |
| 15:25.59 | goxboxlive | # CONFIG_LEDS_TRIGGER_TIMER is not set |
| 15:26.02 | goxboxlive | CONFIG_LEDS_TRIGGER_TIMER_ASIC3=y |
| 15:27.50 | cr2 | CONFIG_LEDS_TRIGGER_TIMER_ASIC3 |
| 15:27.51 | cr2 | this is the only difference. |
| 15:27.52 | goxboxlive | yes |
| 15:27.52 | cr2 | i don't know if we need it actually. |
| 15:28.17 | cr2 | what colours do you see ? |
| 15:28.46 | goxboxlive | Well €1300 for the Athena is very expensive. I guess it will be 1400 here in Norway then. |
| 15:28.59 | goxboxlive | cr2: Hold, i'll boot it |
| 15:30.35 | goxboxlive | hmm i have lost my pen |
| 15:30.58 | cr2 | there are 2 included ? |
| 15:31.12 | goxboxlive | i know |
| 15:31.30 | goxboxlive | ok, what do you want me to test |
| 15:31.47 | goxboxlive | The power led has the same status as in WInCe |
| 15:31.52 | goxboxlive | green blinking |
| 15:32.01 | goxboxlive | I have now plugged in the USB cable |
| 15:33.05 | goxboxlive | cr2: I have BT running and the led is blinking Blue, as it should. |
| 15:33.26 | cr2 | wifi ? |
| 15:33.40 | goxboxlive | I swithed the BT radio off, and the Blue led stopped blinking |
| 15:33.52 | cr2 | the power may need some changes. |
| 15:34.43 | goxboxlive | Wifi led is also blinking, i dont have any connection, but the acx module is loaded. I'll try to unload it now |
| 15:35.51 | goxboxlive | I unloaded the wifi module, but the wifi led is still blinking |
| 15:36.23 | goxboxlive | It works same as it worked before you changed the driver |
| 15:36.54 | goxboxlive | What is this? : 26: 36542 SC PXA Timer Tick |
| 15:38.00 | goxboxlive | I tried root@htcuniversal:~$ modprobe -r htcuniversal_acx and the system froze |
| 15:38.11 | goxboxlive | I have to go now, be back in a couple of hours. |
| 15:46.44 | *** join/#htc-linux pleemans (n=peter@d51A5E612.access.telenet.be) |
| 15:53.24 | cr2 | WizMaui: good :) are there any other omap850 phones ? prophet ? |
| 15:53.36 | WizMaui | yep |
| 15:54.03 | cr2 | add it too. i'll update the mach-types then. |
| 15:54.36 | WizMaui | ok |
| 15:54.53 | WizMaui | but should i assign the same directory name for prophet? |
| 15:56.14 | cr2 | directory name ? |
| 15:59.00 | pH5 | WizMaui: under arch/arm/mach-pxa? no. |
| 16:00.20 | pH5 | cr2: 1300€.. what did the universal cost for when it was new? |
| 16:01.04 | cr2 | arch/arm/mach-omap but is does not really matter. |
| 16:01.43 | pH5 | whoops |
| 16:01.47 | cr2 | pH5: 700€, but then the t-mob increased it to 799€. for some reason. |
| 16:02.24 | cr2 | i have paid 300something, but with the contract. |
| 16:02.47 | cr2 | it was in oct. 2005 |
| 16:03.46 | pH5 | I wonder how they justify the +500€ price tag for the Athena? Is it price per kg? |
| 16:04.21 | cr2 | ati+gps+8GB disk |
| 16:04.39 | cr2 | now i know why they did not solder gps in universal. |
| 16:04.48 | cr2 | and i was right. greed ;) |
| 16:05.34 | cr2 | but i guess the price tag was forced by the providers. |
| 16:06.11 | cr2 | htc wants to squeeze more now from the dumb consumers. |
| 16:06.57 | Kevin2 | Hi |
| 16:07.21 | cr2 | it's just insane to ask for som much when the notebook prices go to the 499€ tag. |
| 16:07.36 | cr2 | hi Kevin2 |
| 16:09.04 | pH5 | cr2: right |
| 16:09.06 | pH5 | hi Kevin2 |
| 16:13.23 | *** join/#htc-linux goxboxlive (n=goxboxli@9.80-202-160.nextgentel.com) |
| 16:13.42 | Kevin2 | Hi goxboxlive |
| 16:15.30 | goxboxlive | Hi Kevin2 |
| 16:16.34 | goxboxlive | It seems like i cant run WIFI (missing driver in WInce), is there any other way to telnet to H5500? |
| 16:19.59 | cr2 | goxboxlive: usb |
| 16:21.05 | cr2 | pH5: magician et al. with TI chipset (hima/ba/alpine) seem to be a cheap big brother device :D |
| 16:22.08 | cr2 | universal (and i guess apache/sable/hermes/trinity) have very fine audio routing control. |
| 16:22.20 | goxboxlive | cr2: From linux -> wince? |
| 16:22.21 | cr2 | but it's probably ak4641 vs. uda1380 |
| 16:22.40 | pH5 | cr2: big brother? how? ;) |
| 16:22.40 | cr2 | goxboxlive: synce |
| 16:23.17 | pH5 | the uda1380 only supports one input and one output at a time (each digital and analog) |
| 16:23.17 | cr2 | pH5: the mic and BT is controlled by the BB |
| 16:23.32 | pH5 | ah :) |
| 16:23.43 | cr2 | on ak4641 all sound routing is through the ak4641 |
| 16:24.05 | cr2 | i don't think they are really evil and have other hidden audio routes :) |
| 16:24.47 | pH5 | cr2: we will only know when somebody decrypts those radio roms ;) |
| 16:24.52 | cr2 | hmm. but can you record the calls ? |
| 16:25.22 | cr2 | pH5: i remember that it was possible on the blueangel. |
| 16:25.35 | pH5 | cr2: no, that won't be possible. the BB output is connected directly to the second internal speaker |
| 16:25.41 | pH5 | wait.. |
| 16:25.45 | cr2 | look for really old ba radio roms. |
| 16:25.56 | pH5 | really? |
| 16:26.18 | pH5 | I wish I could see the code in those roms.. |
| 16:26.31 | cr2 | pH5: the mic is connected to uda1380, so why not switch it on while talking ? |
| 16:27.02 | cr2 | and record the i2s stream. |
| 16:27.28 | pH5 | cr2: right, this part is easy (once I get it working), but that won't record the incoming sound stream. |
| 16:27.39 | pH5 | (or at least only those parts of it that the mic can hear) |
| 16:27.54 | cr2 | is there no handsfree mode on magician ? |
| 16:29.12 | cr2 | pH5: what is really interesting is to do a full BB RAM dump. |
| 16:29.21 | pH5 | not that I know of. |
| 16:29.40 | cr2 | then you don't need to break your head about the location of the entry point. |
| 16:30.00 | cr2 | and other dirty obfuscated things. |
| 16:32.11 | cr2 | huh. hermes names itself HTC_Mercury in the http id ? |
| 16:33.21 | cr2 | ah. ok. |
| 16:35.25 | pH5 | yay, I can wake up the phone with a call |
| 16:35.38 | goxboxlive | cr2: WHat is the telnet port for haret? |
| 16:35.46 | cr2 | 9999 |
| 16:36.01 | pH5 | note to self: if you want drivers to enable PWER bits, don't overwrite PWER in the machine suspend function |
| 16:36.44 | cr2 | Kevin2: the 'HaRET Version pre-0.4.7-200701XXXXXXXX...' |
| 16:36.58 | cr2 | has junk at the end. |
| 16:38.35 | cr2 | Enabling this option allows Remote SIM access over Bluetooth. |
| 16:38.48 | cr2 | hermes is a real secirity nightmare |
| 16:39.40 | cr2 | today i got some junk MMS that tries to connect over GPRS. good that i don't have gprs contract ;-) |
| 16:39.52 | goxboxlive | How do i know the ip adress of wince? |
| 16:40.13 | goxboxlive | I have it connected, RAKI is saying that it is connected |
| 16:40.26 | cr2 | look in dmesg ? |
| 16:41.12 | goxboxlive | usb 1-2: PocketPC PDA converter now attached to ttyUSB0 |
| 16:41.17 | goxboxlive | No ip there |
| 16:41.27 | cr2 | netstat ? |
| 16:41.29 | Kevin2 | cr2: It should be the build date and time. |
| 16:41.43 | maniacxs | goxboxlive: ifconfig pppX |
| 16:41.50 | cr2 | Kevin2: should it be utf16 ? |
| 16:41.54 | maniacxs | goxboxlive: PtP Partner |
| 16:42.18 | cr2 | the \00 is not detected at the end. |
| 16:43.24 | Kevin2 | Okay. General problem with libc calls like snprintf - they don't guarantee a trailing zero. |
| 16:43.26 | goxboxlive | yes i found it, but it refuse the telnet connection |
| 16:44.29 | cr2 | Kevin2: add it manually ? |
| 16:45.00 | Kevin2 | Heh, it is easier to just up the buffer size. :-) |
| 16:45.36 | cr2 | and zero it before sprintf' |
| 16:46.14 | cr2 | hmm. |
| 16:46.53 | cr2 | is it some security setting, of what ? i can access the internet from hermes, download haret, but can't ping it or connect to port 9999 |
| 16:47.21 | Kevin2 | cr2: Through cell network, usb, or wifi? |
| 16:47.48 | cr2 | wiif |
| 16:47.59 | cr2 | usb does not work on wince5. |
| 16:48.27 | cr2 | Kevin2: can we sign haret with some homebrew cert ? |
| 16:49.01 | Kevin2 | cr2: I don't know how to. |
| 16:53.33 | cr2 | i have read something about it, but don't know if it can be done only using openssl. |
| 16:57.28 | *** join/#htc-linux _scatterp (i=scatterp@packet.filtered.ca) |
| 17:01.28 | Hymie | cr2: usb works fine with wince5 now |
| 17:01.35 | Hymie | cr2: using the new drivers |
| 17:01.46 | Hymie | that is, usb + linux |
| 17:02.04 | Hymie | cr2: I get an IP to ping and so on |
| 17:04.15 | Kevin2 | cr2: Were you able to figure out the problem with haret on your jornada? |
| 17:05.41 | cr2 | Kevin2: no, i'm busy with hermes wifi |
| 17:14.53 | *** join/#htc-linux psokolovsky__ (n=psokolov@238.usernat.ip.net.ua) |
| 17:15.48 | *** join/#htc-linux rmoravcik (n=rmoravci@icm1-orange.orange.sk) |
| 17:23.03 | Kevin2 | Hi psokolovsky__ |
| 17:31.52 | Hymie | cr2: haret works here, I just tested |
| 17:31.54 | Hymie | via USB |
| 17:32.11 | Hymie | # telnet 169.254.2.1 9999 |
| 17:32.11 | Hymie | Trying 169.254.2.1... |
| 17:32.11 | Hymie | Connected to 169.254.2.1. |
| 17:32.46 | Hymie | cr2: should I try via wifi? |
| 17:35.44 | Hymie | honestly.. cr2.. whatever your sister says, it isn't true, I didn't do that on our date |
| 18:04.00 | psokolovsky__ | Hi! |
| 18:11.32 | *** join/#htc-linux goxboxlive (n=goxboxli@9.80-202-160.nextgentel.com) |
| 18:20.18 | *** join/#htc-linux rmoravcik (n=rmoravci@icm5-orange.orange.sk) |
| 18:30.20 | cr2 | Hymie: i don't have a sister, thanks God. |
| 18:31.04 | cr2 | i don't understand how the people can use windows. it's such a piece of shit if something is not working. |
| 18:31.09 | cr2 | debugging impossible. |
| 18:31.22 | cr2 | gave up on hermes for some time ;) |
| 18:37.38 | kimuSan^ | hmm anyone that knows the reg setting in winmo5 to remove the lock (times lock after XX minutes where you have to input password/pin to get access again) ? |
| 18:49.17 | *** join/#htc-linux rpodgorny (n=rpodgorn@180.129.broadband3.iol.cz) |
| 18:51.02 | *** join/#htc-linux univac (n=univac@xmms2/user/univac) |
| 18:51.20 | *** part/#htc-linux univac (n=univac@xmms2/user/univac) |
| 18:53.37 | *** join/#htc-linux progeny (n=progeny@asterx.upc.es) |
| 19:21.04 | *** join/#htc-linux apt (i=ibot@pdpc/supporter/active/TimRiker/bot/apt) |
| 19:21.04 | *** topic/#htc-linux is HTC Linux Channel: Find logs at http://apt.rikers.org/%23htc-linux/ | please check http://handhelds.org/moin/moin.cgi/HTC_2dPhones | http://wiki.xda-developers.com/index.php?pagename=Xanadux | <cr2> let's define a common setup. |
| 19:26.57 | Hymie | cr2? |
| 19:27.24 | Hymie | cr2: haret works here over USB.... |
| 19:31.56 | goxboxlive | Kevin2: Are you there? |
| 19:43.44 | goxboxlive | forget it i sent you a mail instead |
| 19:43.59 | oppiz | hey Kevin2 |
| 19:52.59 | *** join/#htc-linux asylumed (n=insanity@196.211.116.2) |
| 19:57.48 | Hymie | well cr2, I don't know what the problem is, but anyhow... I hope you're not grouchy in the future, and whatever's bugging you will be ok |
| 19:59.05 | Kevin2 | Hi |
| 20:03.53 | parmaster | ~statusofblueangel |
| 20:03.55 | apt | rumour has it, statusofblueangel is to be finished |
| 20:04.28 | parmaster | ~statusofapache |
| 20:04.46 | parmaster | heh, guess none of that is actually used |
| 20:06.30 | cr2 | Hymie: i'm doing 10000 things simultaneously, and don't always sit at the computer :) |
| 20:09.39 | BabelO | goxboxlive: is lignokii compiling with OE ? |
| 20:10.03 | Hymie | cr2: well, sure.. but I said many things about USB working for me with hermes wince5 + Linux.... I was just worried that you didn't know about the newer USB drivers |
| 20:10.04 | goxboxlive | wait i'll try |
| 20:10.14 | kimuSan^ | cr2: WHAT! not always by the computer?!?! how is that possible :-P |
| 20:10.23 | Hymie | cr2: I just wondered because you ignored all those comments... yet responded to other people |
| 20:11.07 | Hymie | cr2: so, I'll say again, I just tested haret with wince5 (hermes) + linux USB and telneted successfully.. so I don't know why you say it doesn't work |
| 20:11.33 | goxboxlive | BabelO: you mean gnokii right? |
| 20:11.45 | BabelO | goxboxlive: yes |
| 20:12.50 | goxboxlive | BabelO no it failes |
| 20:13.07 | BabelO | goxboxlive: sniff :( |
| 20:13.19 | goxboxlive | It's becaus eof some NK7110 |
| 20:13.20 | goxboxlive | stuff |
| 20:14.09 | BabelO | goxboxlive: yes i have same problem, if i try the last one it fail with unixserial, so i have to try other between 0.6.9 and 0.6.4 |
| 20:14.31 | cr2 | Hymie: i know that it's possible to run, but it does not run out-of-the-box here, like wifi should do. |
| 20:14.55 | *** join/#htc-linux rmoravcik (n=rmoravci@icm4-orange.orange.sk) |
| 20:16.38 | Hymie | cr2: ok.. if you want, I can do some tests for wifi here.. if it will help you. I'm not a progammer (I can do some coding, but it's not my forte).. however, I am a sysadmin,a nd I can monkey with stuff like this |
| 20:17.01 | Hymie | cr2: if it is something that pisses you off, that makes me feel better if I can get an answer as to what is up, and if it is feasable |
| 20:18.44 | cr2 | Hymie: thanks, but i wanted to have an option of changing the haret code and testing it immediately on the device. |
| 20:20.07 | cr2 | i'm not allowed to run a no-wep setup on the main wifi AP, so i have taken my own from home. but it's a different model, with a different setup and it does not play nice with the other things. |
| 20:20.30 | Hymie | doh |
| 20:20.47 | Hymie | cr2: ok, well, I thought there was something I could do there to help :/ |
| 20:20.54 | Hymie | cr2: sorry for the hassle |
| 20:20.57 | cr2 | why hermes does not want to work with the wrt54G, i have really no idea. other 3 htc devices work. |
| 20:21.23 | Hymie | I remember something about that |
| 20:21.26 | cr2 | i did the full reset, and do the same setup as on other wince5 phones. |
| 20:21.32 | Hymie | I know I had to set a static IP on the hermes to get it to work with my wifi |
| 20:21.40 | Hymie | dhcp didn't work for some reason |
| 20:21.54 | cr2 | but the fucking wince simply does not connect, and i don't see any other way to find out why. |
| 20:22.01 | Hymie | yes |
| 20:22.04 | Hymie | it will tell you so |
| 20:22.06 | Hymie | but that's because dhcp fails |
| 20:22.10 | Hymie | for some retarded reason |
| 20:22.28 | Hymie | at least, that's what happened here, on my dlink, and some other users had that problem |
| 20:22.46 | Hymie | now, I don't know if that's the hermes only, or if it's another generic problem that just sounds related |
| 20:22.54 | cr2 | once i had a problem on BA with the uppercase hex in the wep key. |
| 20:23.00 | Hymie | but because it couldn't do dhcp correctly, it keeps spewing error messages |
| 20:23.02 | cr2 | tried it, did not help. |
| 20:23.05 | Hymie | doh |
| 20:23.59 | cr2 | i'll make a break and will hack on the jornada820 :) |
| 20:24.21 | Hymie | cr2: also, one last thing.. sitting 4M from my wifi hotspot, I have to have hermes in 100% power for it to connect |
| 20:24.41 | Hymie | this too gives an error |
| 20:24.47 | Hymie | which is absurd |
| 20:24.53 | Hymie | my laptop works .. well, 100M away |
| 20:26.48 | Kevin2 | cr2: Are you using wep on the wrt54G? Do you use openwrt? |
| 20:27.16 | Hymie | openwrt rocks, and sucks at the same time ;) |
| 20:27.22 | Hymie | mostly rocks though |
| 20:27.29 | lilliput | have you tried to check what is going on with tcpdump/wireshark ? |
| 20:27.59 | Hymie | kimuSan^: when it works, it is god like ;) |
| 20:28.25 | cr2 | it's standard firmware that i have. not time to move for openwrt |
| 20:41.45 | *** join/#htc-linux rmoravci1 (n=rmoravci@icm7-orange.orange.sk) |
| 20:49.41 | cr2 | Kevin2: i have converted the 32x32 haret.ico in "standard" colors so it shows up also on wince2.11 |
| 20:49.55 | cr2 | with 8bit LCD |
| 20:51.57 | cr2 | hmm. only as a big icon. |
| 20:59.54 | goxboxlive | ~ibot |
| 20:59.56 | apt | ibot is, like, a blootbot written in perl run by TimRiker on his server. logs on http://ibot.rikers.org/<chan>/ , ibot, jbot, apt are all the same process. It uses sqlite, but mysql or other SQL storage is also supported. |
| 21:00.08 | *** join/#htc-linux asylumed (n=insanity@196.211.28.91) |
| 21:00.25 | goxboxlive | ~apt |
| 21:00.27 | apt | apt is probably the debian package manager and nothing to do with ibot |
| 21:01.03 | goxboxlive | ~goxboxlive |
| 21:01.26 | goxboxlive | ~seen Bosjo |
| 21:01.46 | apt | bosjo <n=BoSJo@105.84-48-112.nextgentel.com> was last seen on IRC in channel #htc-linux, 26d 20h 52m 6s ago, saying: 'I see. Ok have a nice day then---gotta go to bed....just gotta take a better look at this new Suse 10.2'. |
| 21:03.39 | goxboxlive | Well last time i checked him he sat and watched TV for allmost 3 months. Now he has been a sleep for 26 days. Man that guy is lazy. |
| 21:10.12 | cr2 | Kevin2: i have compiled my old gnu-haret-sa1100 with cegcc and it works. |
| 21:13.14 | cr2 | Welcome, this is HaRET running on WindowsCE v2.11 |
| 21:13.15 | cr2 | CPU is DEC ARM arch 4 stepping 11 |
| 21:13.15 | cr2 | Running in user mode; minimal virtual address: 00010000, maximal: 7fffffff |
| 21:13.15 | cr2 | Enter 'HELP' for a short command summary. |
| 21:13.28 | cr2 | DEC ARM btw, not Intel ARM. |
| 21:14.25 | *** join/#htc-linux rmoravcik (n=rmoravci@icm7-orange.orange.sk) |
| 21:18.14 | cr2 | goxboxlive: can you remove the old non-angstrom packages ? it confuses people. |
| 21:20.35 | kimuSan^ | is it possible to build haret on linux? |
| 21:23.29 | cr2 | kimuSan^: where do you think we build it ? |
| 21:39.47 | kimuSan^ | the makefile looked like a mingw polluted file so my guess was a win with cyg/ming |
| 21:44.21 | *** join/#htc-linux rpodgorny (n=rpodgorn@180.129.broadband3.iol.cz) |
| 21:45.11 | rpodgorny | is it normal the ba kernel compile fails with?: WARNING: "w1_ds2760_write" [arch/arm/mach-pxa/htcblueangel/blueangel_battery.ko] undefined! |
| 21:45.11 | rpodgorny | WARNING: "w1_ds2760_status" [arch/arm/mach-pxa/htcblueangel/blueangel_battery.ko] undefined! |
| 21:45.12 | rpodgorny | make[1]: *** [__modpost] Error 1 |
| 21:45.12 | rpodgorny | make: *** [modules] Error 2 |
| 21:45.30 | BabelO | rpodgorny: defconfig ? |
| 21:45.32 | rpodgorny | (CVS HEAD) |
| 21:45.43 | rpodgorny | yes |
| 21:46.01 | BabelO | you have to select w1 bus indriver |
| 21:46.07 | BabelO | select ds1wm and ds2760 |
| 21:46.44 | BabelO | CONFIG_W1=m |
| 21:46.53 | BabelO | CONFIG_W1_DS1WM=m |
| 21:47.00 | BabelO | CONFIG_W1_DS2760=m |
| 21:47.22 | rpodgorny | trying with clean defconfig just to be sure |
| 21:47.23 | cr2 | hmm. i thouught i have updated it. |
| 21:47.52 | *** join/#htc-linux g3gg0_ (n=g3gg0@ppp-82-135-0-250.dynamic.mnet-online.de) |
| 21:47.54 | rpodgorny | ah, that may be it :-) ..let's wait a bit and see |
| 21:47.57 | BabelO | cr2: it was late in evening :) |
| 21:49.01 | cr2 | maybe. |
| 21:49.08 | rpodgorny | this second cpu core comes handy when it comes to compilation :-) |
| 21:49.46 | rpodgorny | so sorry for the noise, with fresh ba_defconf it compiles fine |
| 21:50.06 | BabelO | ok good |
| 21:53.13 | cr2 | pH5: are you still around ? |
| 21:55.36 | pH5 | cr2: yes |
| 21:56.07 | kimuSan^ | link to lates tool-chain anyone? |
| 21:58.43 | cr2 | pH5: what is the oldest BA radio rom ? |
| 22:03.14 | pH5 | cr2: I believe it was 1.00. Did you look at ftp.xda-developers.com? |
| 22:04.01 | cr2 | http://wiki.xda-developers.com/index.php?pagename=BA_Upgrades |
| 22:04.03 | cr2 | yes. |
| 22:04.14 | VisN | rpodgorny, I've same problem |
| 22:04.18 | cr2 | T-Mobile UK ENG OP ID 1.06.00 1.06.160 1.00.00 |
| 22:04.24 | pH5 | ftp://xda:xda@ftp.xda-developers.com/BlueAngel/Radio_Roms/O2_UK_XDAIIs_ENG_11262_178_10200_SHIP |
| 22:04.34 | pH5 | from the name this seems to contain a 1.02 version |
| 22:05.13 | cr2 | ok, i've got it. |
| 22:06.08 | cr2 | cabextract -l |
| 22:06.25 | cr2 | 4194476 | 07.03.2005 16:43:20 |
| 22:06.32 | cr2 | uh. really old. |
| 22:08.59 | pH5 | is it encrypted in the same way as the new roms? |
| 22:12.11 | cr2 | don't know. |
| 22:12.17 | cr2 | can't decode it ;) |
| 22:14.21 | cr2 | http://wiki.xda-developers.com/index.php?pagename=xda2nbftool |
| 22:15.03 | pH5 | there are too many different decode programs for those radio roms |
| 22:16.01 | cr2 | yes, and this one does not work too. |
| 22:17.46 | pH5 | xda3nbftools -x radio_.nbf radio_.nba 0x20040523 |
| 22:18.43 | cr2 | WARNING: this does not look like a nbf header, possible you provided the wrong password |
| 22:18.59 | pH5 | use xda3nbftool, not xda2nbftool |
| 22:19.16 | cr2 | yes. |
| 22:19.35 | cr2 | but i don't see the source for it, btw. |
| 22:23.11 | pH5 | cr2: right, me neither :-/ |
| 22:23.32 | pH5 | and still, after decoding they are still in an encrypted format :-( |
| 22:26.38 | cr2 | then they are not decoded properly |
| 22:27.09 | pof | pH5: I guess you can use 'decoderadio.pl' with them |
| 22:27.19 | cr2 | where is it ? |
| 22:27.35 | pof | http://nah6.com/~itsme/cvs-xdadevtools/xda2nbftool/decoderadio.pl |
| 22:27.55 | pof | it's very handy if you want to disassemble the radio after |
| 22:28.39 | pof | i use objdump crosscompiled for arm, and then a tool called 'radare' |
| 22:28.42 | pof | http://news.nopcode.org/gitweb/gitweb.cgi?p=radare.git/.git;a=summary |
| 22:28.52 | cr2 | blueangel 001f12ac-001f1730 ? |
| 22:29.49 | pof | cr2: i think the file is just 'scrambled' in any way so you can't decode |
| 22:30.15 | pof | but after this you can see it has the HTC radio bootloader, and Qualcomm bootloader inside |
| 22:30.24 | pof | and also other parts which are still unknown to me |
| 22:30.46 | cr2 | which file ? |
| 22:31.00 | pof | radio.nb |
| 22:31.15 | pH5 | pof: thanks! that is great to know |
| 22:31.33 | cr2 | ah.ok. |
| 22:31.37 | pof | any radio I mean... i haven't tied with BA... but at least on hermes / tirinty / excalibur / artemis etc... it's the same |
| 22:31.49 | pH5 | but that script doesn't work on the 1.02 rom we just downloaded - how was the translation table found out? |
| 22:32.25 | pof | do you have it in raw or nbf decoded (nba) format ? |
| 22:32.28 | cr2 | maybe it's an offset ? 001f12ac- |
| 22:32.46 | pH5 | cr2: I think those offsets in the comments only mark parts that are similar in both radios |
| 22:33.24 | BabelO | goxboxlive: good i have a modified gnokki on my BA it works :) |
| 22:33.51 | cr2 | BabelO: what is gnokki ? |
| 22:34.21 | cr2 | pof: ida is not very happy with the universal rom. |
| 22:34.23 | BabelO | cr2: sorry it is gnokii |
| 22:34.49 | pH5 | pof: ouch, it was nba. after removing the header it works. and for my magician roms, too. thanks again for pointing this out! |
| 22:34.57 | BabelO | cr2: but i need to had a new driver for HTC AT command |
| 22:35.00 | cr2 | though i can run "strings" for some insight. |
| 22:35.03 | pof | cr2: which rom ? radio? |
| 22:35.13 | cr2 | pof: yes. |
| 22:35.32 | cr2 | there is a htcboot blob at the beginning |
| 22:35.36 | pof | the 'tricky' thing is to find where the code segment starts |
| 22:35.48 | pof | that's why I use radare instead of ida pro |
| 22:35.48 | cr2 | and then a lot of 0xfffff |
| 22:35.59 | cr2 | ok. |
| 22:36.30 | pof | put radare in visual mode, and flip byte-by-byte |
| 22:36.41 | pof | until the assembly code seems "readable" |
| 22:37.11 | pof | i also have a custom tool to find cross references inside the radio, let me see if I cand find it |
| 22:37.16 | cr2 | is it a random offset ? |
| 22:37.56 | pof | it's different in every radio |
| 22:38.14 | cr2 | ok. strange. |
| 22:38.47 | pH5 | what code is it? 32bit armv4? |
| 22:41.23 | cr2 | may be party thumb. i don't know. |
| 22:41.34 | cr2 | s/party/partly/ |
| 22:42.42 | Kevin2 | goxboxlive: Are you around? |
| 22:43.26 | goxboxlive | BabelO: Great |
| 22:43.32 | goxboxlive | Kevin2: Yes now i am |
| 22:44.59 | goxboxlive | BabelO: how did u manage the compile it? Did you edit OE, or did you change the source? |
| 22:45.12 | Kevin2 | Can you try a couple of commands on h5500? Startup haret fresh, and run the following three commands: pd 0xa00a0000 0x2000 ; vd 0x2E0000 0x2000 ; dump cp 15 |
| 22:45.41 | Kevin2 | Post the results, leave the terminal window open, and I'll send you a new dump command after I analyze the results. |
| 22:45.50 | pof | http://pof.eslack.org/hermes-unlocker/patches/xrefs/xrefs-arm.c |
| 22:46.20 | pof | ^^^ this is handy to use with radare, it's not included in cvs, the author did it for me because I requested |
| 22:47.07 | BabelO | goxboxlive: i take latest version 0.6.13 and do some modification for BA because of postfix and prefix |
| 22:47.19 | goxboxlive | ok |
| 22:47.41 | cr2 | pof: ok. i'm creating the core trinity setup for hh.org CVS |
| 22:48.06 | cr2 | goxboxlive: can you manipulate the right LEDs manually ? |
| 22:48.20 | cr2 | can you force the red light, for example ? |
| 22:48.50 | goxboxlive | cr2: Hold, on, am running the H5500 now. I'll try later, ok? |
| 22:49.14 | cr2 | pof: can you dump the hermes registry in ascii form ? |
| 22:49.22 | cr2 | goxboxlive: ok :) |
| 22:49.47 | goxboxlive | Kevin2: Do u want it on mail or pastebin? |
| 22:50.53 | *** join/#htc-linux istrium (n=no@212.45.14.9) |
| 22:55.01 | goxboxlive | Kevin2: The three dumps are send to you on email |
| 22:56.07 | goxboxlive | CR2: Yes, i am booting universal now, what do you want me to test? |
| 22:56.48 | cr2 | the leds control in /sys |
| 22:58.33 | goxboxlive | cr2: Yes i can control the power led turning red |
| 22:58.47 | Kevin2 | goxboxlive: Can you try "dump cp(15)" |
| 22:59.23 | goxboxlive | Kevin2 HaRET(5)# dump cp(15) |
| 22:59.23 | goxboxlive | line 5: No dumper cp(15) available, see HELP DUMP for a list |
| 23:00.06 | goxboxlive | cr2: Also the green led (power) |
| 23:00.49 | goxboxlive | cr2: But not the blue one. |
| 23:02.21 | Kevin2 | goxboxlive: Can you send output from: vd 0x2E0000 0x8000 |
| 23:02.21 | goxboxlive | Kevin2: I got an output, i missed the space |
| 23:04.30 | goxboxlive | Kevin2: The last one was to big for my buffer, i dont get the whole output, cant scroll back that far |
| 23:04.54 | Kevin2 | vd 0x2E0000 0x4000 -- then if you can |
| 23:05.58 | cr2 | goxboxlive: can you turn both red and green on ? or course you can't really enable blue/green bt/wifi LEDs. |
| 23:06.17 | goxboxlive | cr2_ I'll check |
| 23:06.42 | cr2 | kimuSan^: are you asleep ? i have added the minimal trinity support to CVS. |
| 23:07.05 | goxboxlive | cr2: Yes it turns orange |
| 23:07.18 | cr2 | kimuSan^: you can even compile the kernel ;) but i don't think it will run, but YMMV. |
| 23:07.23 | cr2 | goxboxlive: ok. |
| 23:07.42 | cr2 | goxboxlive: so the names are ok now ? |
| 23:07.55 | goxboxlive | cr2: What name? |
| 23:08.05 | cr2 | LED names <-> color |
| 23:08.08 | goxboxlive | yes |
| 23:08.11 | cr2 | ok. |
| 23:08.16 | goxboxlive | good, great work |
| 23:08.19 | kimuSan^ | cr2: sweet |
| 23:08.36 | cr2 | kimuSan^: try it, actually. |
| 23:09.03 | kimuSan^ | how much will it wipe of my trin :-) |
| 23:09.13 | kimuSan^ | do I need to take a backup ? |
| 23:10.40 | cr2 | goxboxlive: all other LEDs - flash, vibra, keyboard, buttons, etc. need their own driver. |
| 23:10.55 | cr2 | kimuSan^: no. it's wince5. |
| 23:12.06 | goxboxlive | cr2: Oh realy, is it a lot of work, if so i think we should take keyboard leds first |
| 23:12.15 | goxboxlive | Kevin2: Sendt |
| 23:12.26 | kimuSan^ | cr2: yeah I just head that some got their flash wiped anyways. |
| 23:12.56 | cr2 | goxboxlive: it's all 1 driver. |
| 23:13.18 | cr2 | kimuSan^: it's an urban legend ;) |
| 23:13.40 | goxboxlive | cr2: Could you update the htcuniversal_defconfig to add the leds so it is default, and also remove the zaurus usb driver |
| 23:13.46 | kimuSan^ | cr2: great :-) love those bedtime stories :-) |
| 23:14.20 | kimuSan^ | cr2: just need to free some space so I can compile (unless you have image etc ready for me :-) |
| 23:14.24 | cr2 | goxboxlive: zaurus is not a problem, but do you really need the trigger driver ? |
| 23:14.46 | goxboxlive | hold on, let me check something |
| 23:14.54 | cr2 | kimuSan^: i have. where i can upload it ? |
| 23:16.29 | goxboxlive | cr2: Maybe not, it compiles without it. |
| 23:17.28 | goxboxlive | cr2: Maybe you also shuold add usb_host while your editing the .config |
| 23:17.32 | kimuSan^ | hmm not here right now (firewall). Wait. I can create an account on one of my servers. |
| 23:18.19 | kimuSan^ | cr2: har much space is needed? |
| 23:18.19 | cr2 | kimuSan^: do you have www access ? |
| 23:18.19 | kimuSan^ | sure |
| 23:18.19 | BabelO | cr2 is this normal ? http://pastebin.ca/308664 |
| 23:18.21 | cr2 | http://jornada820.sf.net/files/uni |
| 23:18.32 | cr2 | 'ztri' file |
| 23:18.37 | kimuSan^ | cr2: all outgoing is open, just not incomming. |
| 23:18.41 | pof | Kevin2: are u online ? |
| 23:19.12 | kimuSan^ | cr2: only that file or the others too ? |
| 23:19.20 | cr2 | only that file |
| 23:19.33 | cr2 | and boot it with latest haret from Kevin2 |
| 23:20.02 | kimuSan^ | link |
| 23:20.10 | kimuSan^ | is that koconnor? |
| 23:20.16 | cr2 | yes. |
| 23:20.18 | pof | does haret assume that zImage is compressed? does it some uncompressing before loading it? |
| 23:20.45 | cr2 | BabelO: what is wrong in this output ? you have enabled CREG=2 ? :) |
| 23:20.52 | cr2 | pof: no. |
| 23:21.12 | cr2 | the zimage starts with its own decompression code. |
| 23:21.24 | cr2 | decompression and relocation. |
| 23:21.42 | pof | ok, thanks :) |
| 23:22.57 | BabelO | cr2: i got 0x02 and 0x16 in return string :( |
| 23:23.07 | kimuSan^ | cr2: steps to load it is ? |
| 23:23.21 | cr2 | BabelO: so what ? |
| 23:23.37 | cr2 | kimuSan^: edit the startup.txt file |
| 23:23.48 | cr2 | KERNEL="ztri" |
| 23:23.51 | kimuSan^ | default.txt you mean ? |
| 23:23.55 | cr2 | and start haret. |
| 23:24.02 | cr2 | or default.txt |
| 23:24.04 | BabelO | cr2: is it normal to have prefix here ? so i ve to remove it from buffer |
| 23:24.56 | kimuSan^ | anything but the kernel line? |
| 23:25.04 | cr2 | goxboxlive: http://pastebin.ca/307805 - gomunicator is TOO fast here. he should wait for AT-Interpreter ready message before moving forward. |
| 23:25.20 | cr2 | kimuSan^: maybe mem=64M |
| 23:25.30 | cr2 | you are going to crash anyway :) |
| 23:26.05 | kimuSan^ | well need to be ok anyways. right now I have a bunch of lines inthere |
| 23:26.07 | kimuSan^ | set ramaddr 0x30000000 |
| 23:26.08 | kimuSan^ | set ramsize 0x04000000 |
| 23:26.08 | kimuSan^ | set kernel "zImage" |
| 23:26.08 | kimuSan^ | set mtype 1178 |
| 23:26.08 | kimuSan^ | set bootspd 0 |
| 23:26.08 | kimuSan^ | set cmdline "root=254:2 init=/sbin/init" |
| 23:26.10 | kimuSan^ | bootlinux |
| 23:27.14 | kimuSan^ | still need bootlinux or? |
| 23:27.17 | goxboxlive | cr2: That might be, but there is a way to override it. Go to tmp folder at gnulinux.biz, and download the system.conf file. Replace the exixting /etc/dbus/sustem.conf with the one you downloaded. |
| 23:27.52 | goxboxlive | BabelO: Yes, gnokii build for me too. Have to try it |
| 23:28.05 | cr2 | kimuSan^: or course :) |
| 23:28.17 | cr2 | goxboxlive: it still does not look right. |
| 23:29.04 | goxboxlive | cr2: That might be, but it works though. Lamikr had the same problem. |
| 23:30.02 | cr2 | kimuSan^: mtype is redundant. mem=64M is needed. root=254:2 does not matter now. set bootspd 0 is the silly penguin stuff. |
| 23:30.32 | cr2 | goxboxlive: if one bug covers the other bug it#s not good. |
| 23:30.51 | goxboxlive | cr2: thats right |
| 23:31.01 | cr2 | kimuSan^: your mtype is not 1178 anyway. |
| 23:31.28 | kimuSan^ | <PROTECTED> |
| 23:31.35 | cr2 | remove it. |
| 23:31.38 | kimuSan^ | ok |
| 23:31.58 | kimuSan^ | "Undefined Mtype" |
| 23:32.10 | cr2 | we need to see something on the screen first. before caring about init= |
| 23:32.27 | cr2 | heh. does your machine detected as trinity ? |
| 23:32.54 | kimuSan^ | I need to telnet in to see that right? |
| 23:33.28 | cr2 | set it to 1225 |
| 23:33.42 | cr2 | no, it should be the first message in the debug window. |
| 23:33.49 | kimuSan^ | Minimal virtual address: 00010000, maximal virtual address: 7FFFFFFF |
| 23:33.50 | kimuSan^ | Detected machine 'Default' (Plat='PocketPC' OEM='TRIN100') |
| 23:33.50 | cr2 | set mtype 1225 |
| 23:33.52 | kimuSan^ | CPU is ARM ARM arch 4T stepping 0 running in system mode |
| 23:34.03 | cr2 | Detected machine 'Default' |
| 23:34.12 | cr2 | it's not detected as trinity. |
| 23:34.23 | cr2 | so haret does not know your mtype. |
| 23:34.30 | cr2 | add |
| 23:34.32 | cr2 | set mtype 1225 |
| 23:34.36 | Kevin2 | I'm here - just looking at goxboxlive's h5500 stuff. |
| 23:34.44 | cr2 | Kevin2: ok. |
| 23:34.52 | kimuSan^ | "error allocated memory will overwrite itself" |
| 23:35.03 | cr2 | to Kevin2 :) |
| 23:35.12 | goxboxlive | I thought that gnokii where some gui app, is it just a shell app? |
| 23:35.27 | kimuSan^ | goxboxlive: there is a gui for it. |
| 23:35.33 | BabelO | goxboxlive: no there is a xgnokii app |
| 23:35.44 | goxboxlive | do you run it BabelO |
| 23:35.55 | BabelO | goxboxlive: the usefull thing is libgnokii :) |
| 23:35.58 | Kevin2 | kimuSan^: Which device? Are you sure your ramaddr is correct? |
| 23:35.58 | cr2 | goxboxlive: the most useful part of gnokii is libgnokii. |
| 23:36.11 | cr2 | Kevin2: trinity. |
| 23:36.15 | cr2 | it's like hermes. |
| 23:36.18 | kimuSan^ | Kevin2: no ramaddr set |
| 23:36.25 | goxboxlive | ic |
| 23:36.42 | kimuSan^ | what should it be? |
| 23:36.44 | cr2 | kimuSan^: set ramaddr 0x30000000 |
| 23:36.54 | cr2 | set ramsize 0x04000000 |
| 23:37.05 | cr2 | but Kevin2 should know better :) |
| 23:37.57 | Kevin2 | goxboxlive: Do you still have that telnet window open to h5500? Can you run "vd 0x2E0000 0x2000" and "dump cp (15)" again? |
| 23:38.35 | kimuSan^ | nice colors on the screen :-) |
| 23:38.49 | kimuSan^ | blue,red,ugly,yellow,black |
| 23:39.06 | cr2 | but no small linux penguin ? |
| 23:39.12 | goxboxlive | no i dont have it open, but i can open it again |
| 23:39.17 | kimuSan^ | no not yet. |
| 23:39.24 | kimuSan^ | should it be there by now :-) |
| 23:39.35 | cr2 | kimuSan^: i guess it hangs. |
| 23:39.52 | kimuSan^ | I did not have the set bootspd 0 |
| 23:39.57 | cr2 | we should disable the serial output putc() |
| 23:40.01 | cr2 | does not matter. |
| 23:40.04 | Kevin2 | kimuSan^: That is the correct signature for hand off to the kernel. |
| 23:40.04 | kimuSan^ | ok |
| 23:40.15 | Kevin2 | Try running "SET KERNELCRC 1" before running boot. |
| 23:40.27 | kimuSan^ | ok |
| 23:40.58 | kimuSan^ | just after the reset :-) |
| 23:41.18 | cr2 | kimuSan^: i can try to comment it out now. |
| 23:41.28 | cr2 | and recompile the kernel. |
| 23:41.49 | kimuSan^ | actually I got this far with the g500 kernel |
| 23:41.53 | kimuSan^ | cr2: sure |
| 23:42.16 | goxboxlive | Kevin2: Sendt |
| 23:43.11 | kimuSan^ | Kevin2: is the script lang. case insensitive? |
| 23:43.53 | kimuSan^ | Kevin2: kernelcrc 1 made it stay a bit before the black line came |
| 23:44.54 | cr2 | hmm. |
| 23:44.58 | cr2 | CONFIG_SERIAL_S3C2410_CONSOLE=y |
| 23:45.34 | kimuSan^ | oops |
| 23:45.37 | Kevin2 | kimuSan^: Yes it is case insensitive. That means your kernel and initrd (if any) successfully crc'd before loading. I'd guess you have a kernel issue. |
| 23:46.09 | cr2 | Kevin2: it seems we may write the IR putc() for uncompress.h |
| 23:46.20 | Kevin2 | goxboxlive: Wow, I officially declare your device as "skrewy". |
| 23:46.58 | Kevin2 | goxboxlive: Does any version of haret work on it? Is it stable? Is there any background process going wild on it? |
| 23:48.17 | goxboxlive | Kevin2: I have never been able to start haret on it |
| 23:48.47 | goxboxlive | I ahev actually never used it before. |
| 23:49.18 | cr2 | kimuSan^: recompiling. |
| 23:49.34 | kimuSan^ | superb |
| 23:49.48 | cr2 | goxboxlive: can you run the gnu-haret and run "vmalloc" and log the output ? |
| 23:50.03 | cr2 | kimuSan^: the model names ? |
| 23:50.25 | kimuSan^ | hmm the old one is a 3660 if I remember correctly. |
| 23:50.42 | goxboxlive | cr2: ok |
| 23:51.14 | goxboxlive | cr2: Where do i get gnu-haret? |
| 23:51.17 | cr2 | kimuSan^: updated. |
| 23:51.47 | Kevin2 | cr2: I asked goxboxlive to dump the mmu table (vd 0x2e0000). Every single query returns different results. |
| 23:51.54 | kimuSan^ | the new one is an h4150 |
| 23:52.23 | lpotter | goboxlive: scribble should build now |
| 23:52.46 | cr2 | goxboxlive: http://jornada820.sf.net/files/haret |
| 23:53.00 | goxboxlive | lpotter, great, then i remove my local hack, thx |
| 23:53.13 | cr2 | kimuSan^: i think both will run linux. |
| 23:53.14 | goxboxlive | cr2: Oh you mean your version. |
| 23:53.44 | cr2 | h4150 is with the keybaord ? |
| 23:53.49 | kimuSan^ | cr2: cool |
| 23:53.54 | kimuSan^ | no there is no keyboard |
| 23:54.01 | cr2 | ok, it's 4350 |
| 23:54.04 | kimuSan^ | simple pda with wifi, |
| 23:54.21 | cr2 | check the new ztri |
| 23:54.39 | kimuSan^ | looks like the same |
| 23:54.44 | kimuSan^ | when booting it |
| 23:54.46 | Kevin2 | pof: What did you want me to look at? |
| 23:55.49 | *** join/#htc-linux tudenbart (n=willi@xdsl-213-196-220-196.netcologne.de) |
| 23:56.13 | goxboxlive | cr2: it wouldnt start |
| 23:58.17 | kimuSan^ | hmm still no penguin :-) |