| 00:03.54 | cr2 | wince ? |
| 00:05.31 | awelux__ | there seams to be only one are affected. |
| 00:05.43 | awelux__ | I don't know the exact address yet |
| 00:07.10 | awelux__ | usb was not the problem |
| 00:07.21 | awelux__ | *cken= (*cken) & 0xfffffcff; worked to set bits |
| 00:07.51 | cr2 | it is * vs. & ~ |
| 00:08.22 | awelux__ | yea. maybe the & won |
| 00:09.41 | cr2 | i don't remember :) |
| 00:10.02 | cr2 | brackets do not hurt. |
| 00:10.08 | awelux__ | when in doubt place brackets |
| 00:16.36 | awelux__ | switching off USBC, USBH and SSP2 has no effect |
| 00:17.03 | awelux__ | the PWMs are enabled. |
| 00:17.42 | awelux__ | Switching them off will switch off display after a few seconds and require a coldboot |
| 00:18.12 | cr2 | pwm is brightness. |
| 00:18.26 | awelux__ | ah. that explains |
| 00:19.38 | cr2 | fscking touchscreen. now i am tired. |
| 00:20.18 | awelux__ | yep. a break is in order. |
| 00:20.39 | cr2 | audio probably needs a 2.6.15 update... |
| 00:21.36 | awelux__ | ah. that would be a lot of work |
| 00:22.39 | cr2 | the umts modem needs a commandline tool for testing. |
| 00:23.04 | cr2 | i will probably try to build opie from oe setup. |
| 00:23.33 | awelux__ | unversal hass umts ? |
| 00:23.37 | cr2 | there are also console touchscreen debug tools. |
| 00:23.40 | cr2 | yes. |
| 00:24.02 | cr2 | but you don't care. |
| 00:24.17 | cr2 | the data goes through serial-over-usb. |
| 00:24.19 | awelux__ | true ;) |
| 00:24.30 | cr2 | that's why i need usb host. |
| 00:24.44 | cr2 | but only for umts, which i don't use anyway :) |
| 00:26.42 | awelux__ | sigh |
| 00:26.52 | awelux__ | I should stop for today. |
| 00:27.00 | awelux__ | The mistakes are getting stupider by the minute |
| 00:27.07 | cr2 | good night. |
| 00:27.24 | awelux__ | bood night cr2 |
| 00:28.43 | awelux__ | *good night |
| 00:32.26 | awelux__ | ok. couldn't resist. it works now ;) |
| 00:32.52 | awelux__ | I switched off MMC, I2C, SSP2 and finally USB |
| 00:41.25 | cr2 | who is working ? |
| 00:41.39 | awelux__ | the decompression works |
| 00:41.50 | awelux__ | I will check how far I get now |
| 00:41.53 | cr2 | ok. maybe boot ? :) |
| 00:42.04 | awelux__ | hihi. not yet |
| 00:45.13 | awelux__ | I still don't reach the init procedures. |
| 00:45.20 | awelux__ | Or the vibra would go off. |
| 00:45.36 | awelux__ | But I'm not far away now. |
| 00:45.53 | cr2 | i guess that vibra is also on pwm. |
| 00:46.38 | awelux__ | pwm is still on |
| 00:54.50 | cr2 | oh. i have compiled the tslib-utils ,copied them over to SD and run. the touchscreen is everything else as linear... |
| 01:09.33 | awelux__ | can tslib handle it ? |
| 01:15.06 | cr2 | i don't know the algorithm they use. |
| 01:15.19 | cr2 | i will post the picture to xda-dev now. |
| 01:20.00 | cr2 | http://forum.xda-developers.com/files/tscal_universal.jpg |
| 01:20.38 | awelux__ | nice |
| 01:21.01 | cr2 | opie has problems with 5-point cal ;) |
| 01:21.12 | cr2 | gpe simply ignores them... |
| 01:22.26 | awelux__ | some work left. I will call it a day now. |
| 01:22.28 | awelux__ | cu. |
| 01:22.35 | cr2 | good night. |
| 06:58.29 | *** join/#htc-blueangel rob_w|mis (n=rob_w@p549BCADB.dip0.t-ipconnect.de) |
| 07:18.33 | *** join/#htc-blueangel cr2 (n=konversa@crpl22.physik.uni-wuppertal.de) |
| 08:24.16 | *** join/#htc-blueangel awelux (n=awelux__@dslb-084-058-135-157.pools.arcor-ip.net) |
| 09:43.15 | awelux | I guess the windows TS calibration uses some vendor dependent setting tto remove the manufacturing process dependent nonlinearities. Then they just use the 5point calibration for finetuning. |
| 09:58.30 | rob_w|mis | normally we run fine by ignoring nonlinear thnings.. they manufacture quite well .. eh |
| 09:59.09 | awelux | not cr2's universal ;) |
| 10:02.27 | rob_w|mis | oh |
| 10:16.28 | cr2 | rob_w: http://forum.xda-developers.com/files/tscal_universal.jpg |
| 10:16.34 | cr2 | hi guys |
| 10:18.55 | awelux | hi. I'm somehow losing the code just before the relocation of the decompressed kernel. |
| 10:20.58 | awelux | I added a dot into both branches but I don't see it. |
| 10:21.09 | cr2 | strange... |
| 10:21.11 | awelux | So I guess the address got corrupted somehow |
| 10:23.41 | awelux | lol |
| 10:23.48 | awelux | ok found the problem |
| 10:23.53 | awelux | bl overwrites r14 |
| 10:23.58 | awelux | which I used |
| 10:27.44 | cr2 | r14=lr, you should save/restore it on stack if you want to use it. |
| 10:28.48 | awelux | I won't have a valid stack pointer once I enter the relocation code. |
| 10:32.18 | cr2 | reserver 1-2 pages and set your own. or don't use r14 :) |
| 10:32.55 | awelux | I'm currently going for the alter |
| 10:32.59 | awelux | *later |
| 10:41.46 | *** join/#htc-blueangel dullard (n=jim@adsl-static-1-30.uklinux.net) |
| 12:00.01 | *** join/#htc-blueangel immolo (i=vraxjotf@cpc3-cosh1-4-0-cust151.cos2.cable.ntl.com) |
| 12:16.54 | *** join/#htc-blueangel immolo (i=ikugxpj@cpc3-cosh1-4-0-cust151.cos2.cable.ntl.com) |
| 14:33.32 | awelux | cr2, can you upload your kernel config somewhere ? |
| 14:46.53 | *** join/#htc-blueangel immolo (i=oonqah@cpc3-cosh1-4-0-cust151.cos2.cable.ntl.com) |
| 14:48.13 | *** join/#htc-blueangel immolo (i=vbsonyvp@cpc3-cosh1-4-0-cust151.cos2.cable.ntl.com) |
| 14:51.28 | *** join/#htc-blueangel immolo (i=uojjemto@cpc3-cosh1-4-0-cust151.cos2.cable.ntl.com) |
| 14:52.24 | cr2 | .config.gz in files/uni |
| 14:53.40 | *** join/#htc-blueangel immolo (i=wfajlrv@cpc3-cosh1-4-0-cust151.cos2.cable.ntl.com) |
| 14:53.42 | cr2 | i have assembled my blueangel! the LCD pixels are too big ;) |
| 14:54.12 | awelux | thx |
| 14:54.15 | cr2 | now i need the unified sdcard for both phones. |
| 14:54.43 | cr2 | i see a lot of space for improvement in the user-friendliness. |
| 14:55.19 | cr2 | will checkout the ba0 branch. maybe even put un0 in ba0... |
| 17:27.11 | *** join/#htc-blueangel jeanseb (n=jeanseb@lns-bzn-47f-62-147-133-94.adsl.proxad.net) |
| 19:09.03 | Funklord | http://vibes.se/dist/stats.c |
| 19:09.07 | Funklord | I was bored ;P |
| 19:26.28 | cr2 | i have booted linux on blueangel. |
| 19:28.20 | Funklord | nice |
| 19:28.37 | cr2 | it should be better ;) |
| 19:28.47 | Funklord | did you try that program on it? |
| 19:28.50 | Funklord | ;P |
| 19:29.02 | Funklord | so what's new about it? |
| 19:29.19 | cr2 | not yet. |
| 19:29.30 | Funklord | heh, it's not really related |
| 19:29.42 | cr2 | many things. the text console font is too small. |
| 19:29.56 | cr2 | the keyboard layout is strange. |
| 19:30.06 | cr2 | can't find . and _ |
| 19:30.12 | Funklord | the text console font was fine before.. |
| 19:31.45 | cr2 | the ramdisk is actually unnecessary. unless you want to format the sdcard. |
| 19:34.20 | Funklord | but the sd card will break quickly when it's used as root... |
| 19:35.15 | cr2 | why ? |
| 19:35.22 | Funklord | logging and such |
| 19:35.51 | cr2 | there is no logging if you are not running "full debian". |
| 19:36.29 | cr2 | it should be even worse on the builtin flash then. |
| 19:36.40 | cr2 | like on zaurus |
| 19:38.18 | cr2 | btw, do you have bluetooth running ? |
| 19:38.30 | Funklord | for now it's the simplest solution.. but in the future something can be done about it... |
| 19:38.47 | Funklord | cr2: no, I haven't used linux on it for a while |
| 19:40.23 | cr2 | i want to run a unified universal/blueangel system. |
| 19:40.50 | cr2 | don't see where is the hci setup located. |
| 19:41.08 | cr2 | on universal i don't even know which bt chipset is used ;) |
| 19:41.18 | Funklord | heh |
| 19:42.22 | cr2 | sdptool says only "texas instruments" |
| 19:42.52 | cr2 | i did not know the touchscreen chip too, but guessed it. |
| 19:43.15 | Funklord | got access to the gsm chip? |
| 19:43.33 | Funklord | thru serial |
| 19:44.04 | cr2 | i don't have a good console tool for that. |
| 19:44.21 | cr2 | need to write it first. |
| 19:44.23 | Funklord | I need to go home |
| 19:44.27 | Funklord | ttyl |
| 19:44.44 | cr2 | 0x16 0x2 wrapping is a problem. |
| 20:07.41 | jeanseb | hi cr2 |
| 20:10.44 | cr2 | hi jeanseb |
| 20:11.03 | jeanseb | ok i got few minute to experiment with haret |
| 20:11.05 | cr2 | i have repaired my blueangel and have a lot of problems now;) |
| 20:11.15 | jeanseb | tell me about how to use it if you don't mind |
| 20:11.27 | jeanseb | repaired ? |
| 20:11.27 | cr2 | to use what ? |
| 20:11.31 | jeanseb | haret |
| 20:11.50 | cr2 | i broke the lcd in august last year. |
| 20:12.46 | cr2 | what do you want to do with haret ? |
| 20:13.41 | jeanseb | first use it to display window CE internal |
| 20:13.47 | jeanseb | first how use it to display window CE internal |
| 20:14.21 | cr2 | internal what ? |
| 20:15.15 | cr2 | it is mainly designed to inverstigate the hardware |
| 20:15.23 | jeanseb | ah ok |
| 20:15.33 | jeanseb | so not what i really need |
| 20:15.35 | cr2 | i have added the "dump wince" command to print some useful info. |
| 20:15.49 | jeanseb | ok |
| 20:15.56 | jeanseb | and to connect how do i do ? |
| 20:16.01 | jeanseb | serial ? |
| 20:16.03 | cr2 | there is "dump pxa27x" command, but you have pxa263 cpu, so the output will be distorted. |
| 20:16.18 | cr2 | IP. |
| 20:16.31 | cr2 | i use wireless. |
| 20:17.30 | jeanseb | so telnet ? |
| 20:18.18 | cr2 | yes. telnet over wireless. |
| 20:19.47 | jeanseb | jeanseb@norate:~/pda/photos$ telnet 192.168.0.3 |
| 20:19.47 | jeanseb | Trying 192.168.0.3... |
| 20:19.47 | jeanseb | telnet: Unable to connect to remote host: Connection refused |
| 20:19.58 | jeanseb | stupid am i |
| 20:20.10 | jeanseb | got to run haret first ! |
| 20:21.09 | cr2 | :) |
| 20:21.18 | jeanseb | nothing better |
| 20:22.07 | jeanseb | ok port is 9999 |
| 20:23.10 | jeanseb | i think i ' ll have to patch haret a little but fist have to check what i want to get fro mwin CE |
| 20:23.24 | jeanseb | WMALLOC to allocate memory right ? |
| 20:24.21 | cr2 | KMALLOC to allocate contiguous block |
| 20:24.31 | jeanseb | testing it |
| 20:24.39 | cr2 | VMALLOC to allocate all "virtual" memory |
| 20:24.41 | jeanseb | paddr is physicall adress ? |
| 20:24.51 | cr2 | WMALLOC to test GetKPhys |
| 20:24.54 | cr2 | yes. |
| 20:25.27 | jeanseb | so if we patch kernel to use limited physical memory it ok ? |
| 20:26.37 | cr2 | you can try :) |
| 20:26.52 | jeanseb | checking if param already exist ! |
| 20:26.58 | cr2 | there is a mem= command line param |
| 20:27.46 | cr2 | but it will not be very easy ... |
| 20:28.50 | jeanseb | memmap |
| 20:29.06 | jeanseb | memmap seem to be what i want ! |
| 20:30.09 | jeanseb | will google usage of this param this WE |
| 20:30.32 | jeanseb | KMALLOC of 2526 pages: paddr=a4da1000 vaddr=0 |
| 20:30.32 | jeanseb | <PROTECTED> |
| 20:30.38 | jeanseb | ^haret answer |
| 20:30.49 | jeanseb | is this meaning haret had reserved the block ? |
| 20:32.19 | jeanseb | cr2, ? |
| 20:37.27 | cr2 | it could allocate a block of 2526 |
| 20:38.04 | cr2 | pages. the rest is fragmented. |
| 20:39.57 | jeanseb | ok so if i force (with memmmap param) linux to stay in this block and allocate it with vmalloc) it's good |
| 20:40.43 | jeanseb | 10 meg is very litlle memroy but should be enought for kernel testing |
| 20:40.52 | jeanseb | what your opinion ? |
| 20:40.56 | cr2 | yes. but you need 1. to explain haret not to move the kernel to 0x0 |
| 20:41.17 | cr2 | 2. the base address is hardcorded somewhere in the kernel. |
| 20:41.27 | cr2 | ZMEMRELADDR or something like that. |
| 20:42.19 | jeanseb | ok will take a look to a way to move block before. |
| 20:42.36 | jeanseb | but without spending so muchh time , it is just debug temp stuff |
| 20:43.05 | jeanseb | but as it should be useful for "next " project should be interesting ;) |
| 20:43.11 | jeanseb | aok dodo time now |
| 22:21.10 | *** join/#htc-blueangel immolo (i=hnmcwa@cpc3-cosh1-4-0-cust151.cos2.cable.ntl.com) |
