01:22.46 | *** join/#elinux Taalas (~Taalas@p5B1659D8.dip.t-dialin.net) |
01:27.28 | *** join/#elinux krushia (~krushia@h69-131-92-179.cntcnh.dsl.dynamic.tds.net) |
02:21.53 | *** join/#elinux krushia (~krushia@h69-131-92-179.cntcnh.dsl.dynamic.tds.net) |
03:15.24 | rue_mohr | hello again |
03:16.15 | rue_mohr | to build the replacement hammer kernel, I need uclibc, right? |
03:31.10 | *** join/#elinux rue_shop3 (~rue_mohr@24.207.119.38) |
03:31.23 | rue_shop3 | ashes! |
03:40.07 | wmat | rue_shop3: heh, I see you found it |
03:40.56 | *** join/#elinux rue_shop (~rue_mohr@24.207.119.38) |
03:41.16 | rue_shop | hello, do I need to install uclibc before compiling a new kernel for my hammer board? |
03:41.29 | wmat | rue_shop3: http://elinux.org/Hammer_How_to_build_Kernel |
03:41.44 | rue_shop | yea last I looked its not at all clear |
03:42.00 | wmat | yes, use uclibc |
03:42.32 | rue_shop | ok, is buildroot how I set up uclibc? |
03:43.25 | rue_shop | see that page mentions uclibc, but not how to get or set it up |
03:44.09 | wmat | yes, use buildroot |
03:44.26 | rue_shop | I'm not clear from the buildroot page if it is the means to set up uclibc or not |
03:44.27 | rue_shop | ok |
03:44.47 | rue_shop | so, a) install uclibc, apply hammer .config, compile? |
03:45.52 | rue_shop | then I get the kernel source, apply the hammer kernel config from 2.6.22, build it as an oldconfig, mod it to fit the hammer as per the webpage on building the hammer kernel |
03:46.37 | rue_shop | be nice, I'v never dont this before |
03:46.43 | wmat | well, buildroot can generate a uclibc toolchain |
03:46.55 | wmat | i haven't done this for years either |
03:47.34 | rue_shop | arg, I have to fix all my debian package soruces first |
03:48.52 | wmat | i think you need to build a uclibc toolchain with buildroot, then do your kernel compile using the arm-linux-uclibc- toolchain |
03:49.27 | wmat | i can't remember though, and I'm off to bed. |
03:49.38 | rue_shop | yea my evening is falling short toto |
05:57.08 | *** join/#elinux lyakh (~lyakh@p57BD15A1.dip0.t-ipconnect.de) |
07:23.54 | *** join/#elinux pb__ (~pb@blundell.swaffham-prior.co.uk) |
08:18.25 | *** join/#elinux pb__ (~pb@blundell.swaffham-prior.co.uk) |
09:14.36 | *** join/#elinux Roland (~roland@88-196-10-85-wifi.kjj.estpak.ee) |
10:16.42 | *** join/#elinux pirho (debian-tor@gateway/tor-sasl/pirho) |
11:06.20 | *** join/#elinux pirho (debian-tor@gateway/tor-sasl/pirho) |
12:06.36 | *** join/#elinux gustavoz (~gustavoz@host91.201-252-5.telecom.net.ar) |
15:17.55 | *** join/#elinux ibot (~ibot@rikers.org) |
15:17.55 | *** topic/#elinux is Embedded Linux || http://eLinux.org/ || Please ask anything, however this is a low volume channel therefore it may take 24 hours (or longer) to get a response. Please be patient. |
15:17.56 | *** mode/#elinux [+o ibot] by ChanServ |
15:26.02 | *** join/#elinux roxfan (dunno@91.180.65.71) |
16:21.32 | *** join/#elinux dijenerate (~dijenerat@64.210.44.37) |
19:18.48 | *** join/#elinux toi (~toi@d54C2AA76.access.telenet.be) |
19:55.54 | *** join/#elinux lulinha (~dummy@nkvd.ath.cx) |
19:55.54 | *** part/#elinux lulinha (~dummy@nkvd.ath.cx) |
20:01.20 | *** join/#elinux lulinha (~dummy@nkvd.ath.cx) |
20:01.20 | *** part/#elinux lulinha (~dummy@nkvd.ath.cx) |
20:47.11 | *** part/#elinux flavioribeiro (~flavio@li20-198.members.linode.com) |
20:47.14 | *** join/#elinux flavioribeiro (~flavio@li20-198.members.linode.com) |
23:25.24 | *** join/#elinux ibot (~ibot@rikers.org) |
23:25.24 | *** topic/#elinux is Embedded Linux || http://eLinux.org/ || Please ask anything, however this is a low volume channel therefore it may take 24 hours (or longer) to get a response. Please be patient. |
23:25.24 | *** mode/#elinux [+o ibot] by ChanServ |